5 open source boards using the STMPS2151STR
Real designs built with the STMPS2151STR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
FlightComputer
akkdong
148 × 102 mm409 parts4LNo license2STM32
Dev Board STM32F769
MarvinBrth
52 × 52 mm138 parts6LNo license1STM32
Mainboard v13
TIGERs-Mannheim
80 × 85 mm118 parts4LCustom license9STM32
Stm32 official prototype
blakep7
103.6 × 114.1 mm73 parts4LNo license1Raspberry Pi
CM5 MINIMA
claynicholson
61.2 × 64.2 mm70 parts6LMIT102
How designs wire the STMPS2151STR
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the STMPS2151STR connects to, and the resistors, capacitors and other passives placed on it.
- The IN pin is tied to 5V on 4 of 5 designs.
- The OUT pin has a capacitor to GND on 3 of 5 designs, most often 100 nF (then 10 µF).
- The OUT pin has a series resistor on 3 of 5 designs, most often 0 Ω (then 33 Ω).
- The FAULT pin has a pull-up to VCC_MCU on 3 of 5 designs, most often 47 kΩ (then 3.3 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OUTpin 1 | Connected to: A connector 80%, USBLC6-2SC6 40% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| FAULTpin 3 | Connected to: Signal 60% · not connected 40% |
|
| ENpin 4 | Connected to: The microcontroller 40% · 5V 20% |
|
| INpin 5 | Connected to: 5V 80% · a signal 20% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include CM5 MINIMA by claynicholson, Mainboard v13 by TIGERs-Mannheim, FlightComputer by akkdong and Stm32 official prototype by blakep7.
The STMPS2151STR in open source designs
The gallery holds 5 open source boards using the STMPS2151STR from 5 GitHub repositories; a typical one measures about 80 × 85 mm and carries around 118 components.
100% use four copper layers or more, and 20% carry an open source license.
The most starred is CM5 MINIMA by claynicholson.
Parts used alongside the STMPS2151STR
Microcontrollers on boards using the STMPS2151STR
What boards using the STMPS2151STR are built for
STMPS2151STR: common questions
Where can I find a STMPS2151STR reference design?
Each of the 5 boards on this page is a real design using the STMPS2151STR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the STMPS2151STR IN pin connected?
The IN pin is tied to 5V on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the STMPS2151STR.
How is the STMPS2151STR OUT pin connected?
The OUT pin has a capacitor to GND on 3 of 5 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the STMPS2151STR.
What pull-up resistor is used on the STMPS2151STR FAULT pin?
The FAULT pin has a pull-up to VCC_MCU on 3 of 5 designs, most often 47 kΩ (then 3.3 kΩ). Counted from the KiCad layouts of 5 open source designs using the STMPS2151STR.
Which microcontrollers do boards using the STMPS2151STR use?
Most are built on STM32 (4) and Raspberry Pi (1).
How big is a typical board using the STMPS2151STR?
The median is 80 × 85 mm, and 0% are two-layer designs.
What is the most popular open source board using the STMPS2151STR?
By GitHub stars, CM5 MINIMA by claynicholson, with 102 stars.
Can I simulate one of these boards using the STMPS2151STR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.