6 open source boards using the SX1308

Real designs built with the SX1308, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the SX1308

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the SX1308 connects to, and the resistors, capacitors and other passives placed on it.

  • The SW pin has a inductor on 6 of 6 designs, most often 1 µH (then 100 mH).
  • The FB pin has a resistor to GND on 6 of 6 designs, most often 1 kΩ (then 20.5 kΩ).
  • The VIN pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 10 µF).
  • The VIN pin has a inductor on 4 of 6 designs, most often 1 µH (then 100 mH).
SWpin 1Connected to: Signal 100%
  • Inductor on 100% · 1 µH (1), 100 mH (1)
GNDpin 2Connected to: GND 100%
FBpin 3Connected to: Signal 100%
  • Resistor to GND on 100% · 1 kΩ (1), 20.5 kΩ (1), 30 kΩ (1)
  • Series resistor on 50% · 191 kΩ (1)
  • Pull-up to 5V on 33% · 150 kΩ (1), 220 kΩ (1)
ENpin 4Connected to: A connector 33% · BATT 33%
  • Capacitor to GND on 50% · 10 µF (3), 100 nF (2), 22 µF (1)
  • Inductor on 50% · 100 mH (1)
VINpin 5Connected to: BATT 67% · a signal 33%
  • Decoupling capacitor on 100% · 100 nF (4), 10 µF (4), 22 µF (2)
  • Inductor on 67% · 1 µH (1), 100 mH (1)
NCpin 6Connected to: Not connected 83% · VIN 17%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include S3thermal by 11tools, 遥控器 by CodonNine, Nwpi pcb by elektricM and Sx1308 breakout by ep-infosec.

The SX1308 in open source designs

The gallery holds 6 open source boards using the SX1308 from 6 GitHub repositories; a typical one measures about 74.9 × 67.5 mm and carries around 53 components.

100% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.

The most starred is S3thermal by 11tools.

Parts used alongside the SX1308

Microcontrollers on boards using the SX1308

What boards using the SX1308 are built for

SX1308: common questions

Where can I find a SX1308 reference design?

Each of the 6 boards on this page is a real design using the SX1308. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the SX1308 SW pin connected?

The SW pin has a inductor on 6 of 6 designs, most often 1 µH (then 100 mH). Counted from the KiCad layouts of 6 open source designs using the SX1308.

What resistor goes on the SX1308 FB pin?

The FB pin has a resistor to GND on 6 of 6 designs, most often 1 kΩ (then 20.5 kΩ). Counted from the KiCad layouts of 6 open source designs using the SX1308.

What decoupling capacitors do designs use on the SX1308 VIN pin?

The VIN pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 6 open source designs using the SX1308.

Which microcontrollers do boards using the SX1308 use?

Most are built on STM32 (2) and ESP32 (1).

How big is a typical board using the SX1308?

The median is 74.9 × 67.5 mm, and 100% are two-layer designs.

What is the most popular open source board using the SX1308?

By GitHub stars, S3thermal by 11tools, with 7 stars.

Can I simulate one of these boards using the SX1308 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part