6 open source boards using the TCA9406DCUR

Real designs built with the TCA9406DCUR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the TCA9406DCUR

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TCA9406DCUR connects to, and the resistors, capacitors and other passives placed on it.

  • The VCCA pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 4.7 µF).
  • The VCCB pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 22 µF).
  • The SDA_B pin has a series resistor on 2 of 5 designs, most often 0 Ω (then 1.6 kΩ).
  • The SDA_A pin has a series resistor on 2 of 5 designs, most often 0 Ω.
SDA_Bpin 1Connected to: A connector 40% · GND 20%
  • Series resistor on 40% · 0 Ω (1), 1.6 kΩ (1)
GNDpin 2Connected to: GND 100%
VCCApin 3Connected to: 3.3V 60% · GND 20% · a signal 20%
  • Decoupling capacitor on 80% · 100 nF (6), 4.7 µF (1), 1 µF (1)
SDA_Apin 4Connected to: Signal 100%
  • Series resistor on 40% · 0 Ω (1)
SCL_Apin 5Connected to: Signal 80% · 3.3V 20%
  • Series resistor on 40% · 0 Ω (1)
OEpin 6Connected to: Signal 60% · GND 20% · 3.3V 20%
  • Capacitor to GND on 40% · 100 nF (4), 4.7 µF (1), 1 µF (1)
  • Pull-up to 1.8V on 40% · 1 kΩ (1), 10 kΩ (1)
VCCBpin 7Connected to: 5V 60% · GND 20% · a signal 20%
  • Decoupling capacitor on 80% · 100 nF (3), 22 µF (1), 47 µF (1)
SCL_Bpin 8Connected to: A connector 40% · 3.3V 20%
  • Series resistor on 40% · 0 Ω (1), 1.6 kΩ (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include FMC MIPI by VideoGPU, Oe acquisition board gen3 by open-ephys, Zynqinator by rkarl2 and Trunk imu by Leif-Rydenfalk.

The TCA9406DCUR in open source designs

The gallery holds 6 open source boards using the TCA9406DCUR from 5 GitHub repositories; a typical one measures about 78.2 × 103.5 mm and carries around 114 components.

83% use four copper layers or more, and 50% carry an open source license.

The most starred is FMC MIPI by VideoGPU.

Microcontrollers on boards using the TCA9406DCUR

What boards using the TCA9406DCUR are built for

TCA9406DCUR: common questions

Where can I find a TCA9406DCUR reference design?

Each of the 6 boards on this page is a real design using the TCA9406DCUR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the TCA9406DCUR VCCA pin?

The VCCA pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 5 open source designs using the TCA9406DCUR.

What decoupling capacitors do designs use on the TCA9406DCUR VCCB pin?

The VCCB pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 22 µF). Counted from the KiCad layouts of 5 open source designs using the TCA9406DCUR.

What resistor goes on the TCA9406DCUR SDA_B pin?

The SDA_B pin has a series resistor on 2 of 5 designs, most often 0 Ω (then 1.6 kΩ). Counted from the KiCad layouts of 5 open source designs using the TCA9406DCUR.

Which microcontrollers do boards using the TCA9406DCUR use?

Most are built on FPGA (1).

How big is a typical board using the TCA9406DCUR?

The median is 78.2 × 103.5 mm, and 17% are two-layer designs.

What is the most popular open source board using the TCA9406DCUR?

By GitHub stars, FMC MIPI by VideoGPU, with 22 stars.

Can I simulate one of these boards using the TCA9406DCUR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part