5 open source boards using the TCA9546APWR

Real designs built with the TCA9546APWR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

5 boardsClear filters|Most starred

How designs wire the TCA9546APWR

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TCA9546APWR connects to, and the resistors, capacitors and other passives placed on it.

  • The RESET_N pin has a pull-up to 3.3V on 4 of 5 designs, most often 1 kΩ (then 4.7 kΩ).
  • The VCC pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF).
  • The A0 pin is tied to GND on 4 of 5 designs.
  • The A1 pin is tied to GND on 4 of 5 designs.
A0pin 1Connected to: GND 80% · a signal 20%
A1pin 2Connected to: GND 80% · a signal 20%
RESET_Npin 3Connected to: A connector 40%, the microcontroller 40%
  • Pull-up to 3.3V on 80% · 1 kΩ (2), 4.7 kΩ (1), 100 kΩ (1)
SD0pin 4Connected to: A connector 60%
  • Pull-up to 3.3V on 60% · 1 kΩ (2), 4.7 kΩ (1)
  • Series resistor on 40% · 1 kΩ (1), 5.6 kΩ (1)
SC0pin 5Connected to: A connector 60%
  • Pull-up to 3.3V on 60% · 1 kΩ (2), 4.7 kΩ (1)
  • Series resistor on 40% · 1 kΩ (1), 5.6 kΩ (1)
SD1pin 6Connected to: A connector 40%
  • Pull-up to 3.3V on 60% · 1 kΩ (2), 4.7 kΩ (1)
  • Series resistor on 60% · 0 Ω (2), 1 kΩ (1), 5.6 kΩ (1)
SC1pin 7Connected to: A connector 40%
  • Pull-up to 3.3V on 60% · 1 kΩ (2), 4.7 kΩ (1)
  • Series resistor on 60% · 0 Ω (2), 1 kΩ (1), 5.6 kΩ (1)
GNDpin 8Connected to: GND 100%
SD2pin 9Connected to: A connector 40%
  • Pull-up to 3.3V on 60% · 1 kΩ (2), 4.7 kΩ (1)
  • Series resistor on 40% · 1 kΩ (1), 5.6 kΩ (1)
SC2pin 10Connected to: A connector 40%
  • Pull-up to 3.3V on 60% · 1 kΩ (2), 4.7 kΩ (1)
  • Series resistor on 40% · 1 kΩ (1), 5.6 kΩ (1)
SD3pin 11Connected to: Signal 80% · not connected 20%
  • Pull-up to 3.3V on 60% · 1 kΩ (2), 4.7 kΩ (1)
  • Series resistor on 40% · 0 Ω (1), 1 kΩ (1)
SC3pin 12Connected to: Signal 80% · not connected 20%
  • Pull-up to 3.3V on 60% · 1 kΩ (2), 4.7 kΩ (1)
  • Series resistor on 40% · 0 Ω (1), 1 kΩ (1)
A2pin 13Connected to: GND 80% · a signal 20%
SCLpin 14Connected to: A connector 40%, the microcontroller 40%
  • Pull-up to 3.3V on 40% · 1 kΩ (3)
  • Series resistor on 40% · 0 Ω (4), 5.6 kΩ (1)
SDApin 15Connected to: A connector 40%, the microcontroller 40%
  • Pull-up to 3.3V on 40% · 1 kΩ (3)
  • Series resistor on 40% · 0 Ω (3), 5.6 kΩ (1)
VCCpin 16Connected to: 3.3V 100%
  • Decoupling capacitor on 80% · 100 nF (7), 10 µF (2)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Roboy 3.0 40mm magnetic field calibration by Roboy, Mangoh red by leoheck, SoM V2 by robotique-udes and Myo shield by Roboy.

The TCA9546APWR in open source designs

The gallery holds 5 open source boards using the TCA9546APWR from 5 GitHub repositories; a typical one measures about 76.8 × 62.6 mm and carries around 168 components.

60% use four copper layers or more, and 80% carry an open source license.

The most starred is Roboy 3.0 40mm magnetic field calibration by Roboy.

Microcontrollers on boards using the TCA9546APWR

What boards using the TCA9546APWR are built for

TCA9546APWR: common questions

Where can I find a TCA9546APWR reference design?

Each of the 5 boards on this page is a real design using the TCA9546APWR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the TCA9546APWR RESET_N pin?

The RESET_N pin has a pull-up to 3.3V on 4 of 5 designs, most often 1 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 5 open source designs using the TCA9546APWR.

What decoupling capacitors do designs use on the TCA9546APWR VCC pin?

The VCC pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the TCA9546APWR.

How is the TCA9546APWR A0 pin connected?

The A0 pin is tied to GND on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the TCA9546APWR.

Which microcontrollers do boards using the TCA9546APWR use?

Most are built on ESP32 (1) and STM32 (1).

How big is a typical board using the TCA9546APWR?

The median is 76.8 × 62.6 mm, and 40% are two-layer designs.

What is the most popular open source board using the TCA9546APWR?

By GitHub stars, Roboy 3.0 40mm magnetic field calibration by Roboy, with 6 stars.

Can I simulate one of these boards using the TCA9546APWR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part