13 open source boards using the TLV3201AIDBVR

Real designs built with the TLV3201AIDBVR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

13 boardsClear filters|Most starred

How designs wire the TLV3201AIDBVR

Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the TLV3201AIDBVR connects to, and the resistors, capacitors and other passives placed on it.

  • The IN+ pin has a series resistor on 7 of 9 designs, most often 1 kΩ (then 1 MΩ).
  • The OUT pin has a series resistor on 6 of 9 designs, most often 1 MΩ (then 1 kΩ).
  • The VCC pin has a decoupling capacitor on 6 of 9 designs, most often 100 nF (then 1 µF).
  • The IN+ pin has a resistor to GND on 5 of 9 designs, most often 249 kΩ (then 10 kΩ).
OUTpin 1Connected to: A connector 22%, UCC27511DBVR 22%
  • Series resistor on 67% · 1 MΩ (2), 1 kΩ (1), 22 Ω (1)
  • Resistor to GND on 33% · 19.6 kΩ (2), 100 kΩ (1)
GNDpin 2Connected to: GND 100%
IN+pin 3Connected to: Signal 100%
  • Series resistor on 78% · 1 kΩ (2), 1 MΩ (2), 150 kΩ (1)
  • Resistor to GND on 56% · 249 kΩ (2), 10 kΩ (2), 6.81 kΩ (1)
  • Pull-up to VBUS on 33% · 1 MΩ (2), 3.9 kΩ (1)
IN-pin 4Connected to: Signal 67% · VREF 33%
  • Series resistor on 44% · 210 kΩ (1), 4.7 kΩ (1), 10 kΩ (1)
  • Pull-up to 5V on 44% · 1.2 MΩ (2), 47 kΩ (1), 2.2 MΩ (1)
  • Capacitor to GND on 33% · 100 nF (2), 10 nF (1)
VCCpin 5Connected to: 3.3V 78% · a signal 22%
  • Decoupling capacitor on 67% · 100 nF (12), 1 µF (5)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include OpenGammaKit by vikulin, Cf mp3-player by will127534, Dvk mx8m bsb by gralco and ACTUATOR SUPPORT BOARD - UNVALIDATED PROTOTYPE by darshp848.

The TLV3201AIDBVR in open source designs

The gallery holds 13 open source boards using the TLV3201AIDBVR from 9 GitHub repositories; a typical one measures about 90 × 75 mm and carries around 80 components.

77% use four copper layers or more, and 38% carry an open source license.

The most starred is OpenGammaKit by vikulin.

Microcontrollers on boards using the TLV3201AIDBVR

TLV3201AIDBVR: common questions

Where can I find a TLV3201AIDBVR reference design?

Each of the 13 boards on this page is a real design using the TLV3201AIDBVR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the TLV3201AIDBVR IN+ pin?

The IN+ pin has a series resistor on 7 of 9 designs, most often 1 kΩ (then 1 MΩ). Counted from the KiCad layouts of 9 open source designs using the TLV3201AIDBVR.

What resistor goes on the TLV3201AIDBVR OUT pin?

The OUT pin has a series resistor on 6 of 9 designs, most often 1 MΩ (then 1 kΩ). Counted from the KiCad layouts of 9 open source designs using the TLV3201AIDBVR.

What decoupling capacitors do designs use on the TLV3201AIDBVR VCC pin?

The VCC pin has a decoupling capacitor on 6 of 9 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 9 open source designs using the TLV3201AIDBVR.

What parts are used alongside the TLV3201AIDBVR?

The 1028-1109-1, 1219-1077-1, 1611-MIC5365-2.85YC5-, 1727-7019-1 and 428-200007-MG01 appear in the most repositories here.

Which microcontrollers do boards using the TLV3201AIDBVR use?

Most are built on RP2040/RP2350 (2), STM32 (2) and Raspberry Pi (1).

How big is a typical board using the TLV3201AIDBVR?

The median is 90 × 75 mm, and 23% are two-layer designs.

What is the most popular open source board using the TLV3201AIDBVR?

By GitHub stars, OpenGammaKit by vikulin, with 19 stars.

Can I simulate one of these boards using the TLV3201AIDBVR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part