14 open source boards using the TLV76701DRVR
Real designs built with the TLV76701DRVR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Raspberry Pi
Soleil hardware
protolux-electronics
65 × 30 mm66 parts4LCERN-OHL-P-2.022After
DD1SB
180 × 140 mm287 parts2LMIT0ESP32
LumaDD
xeno3dev
191.9 × 92.3 mm150 parts2LCC-BY-NC-4.00STM32
Relay bypass
jer-lil
57 × 37 mm48 parts4LGPL-3.00STM32
OBC-Flight
Kmshanley
40 × 40 mm78 parts8LGPL-3.03Before
DD1SB
180 × 140 mm287 parts2LMIT0Dfm-2oz
DD1SB
180 × 140 mm287 parts2LMIT0Dfm special finish
DD1SB
180 × 140 mm287 parts2LMIT0E2-native
DD1SB
180 × 140 mm287 parts2LMIT0E4-native
DD1SB
180 × 140 mm287 parts2LMIT0E4R1-baseline
DD1SB
180 × 140 mm287 parts2LMIT0RF2M
DD1SB
150 × 110 mm287 parts2LMIT0Sliver only
DD1SB
180 × 140 mm287 parts2LMIT0Strict before
DD1SB
180 × 140 mm287 parts2LMIT0
How designs wire the TLV76701DRVR
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TLV76701DRVR connects to, and the resistors, capacitors and other passives placed on it.
- The FB pin has a resistor to GND on 5 of 5 designs, most often 200 kΩ (then 160 kΩ).
- The IN pin has a capacitor to GND on 5 of 5 designs, most often 4.7 µF (then 1 µF).
- The FB pin has a pull-up to 6V on 4 of 5 designs, most often 1.2 MΩ (then 200 kΩ).
- The OUT pin is tied to 6V on 4 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OUTpin 1 | Connected to: 6V 80% · a signal 20% | — |
| FBpin 2 | Connected to: Signal 100% |
|
| GNDpin 3, 5 | Connected to: GND 100% | — |
| ENpin 4 | Connected to: Signal 60% · not connected 20% · VBUS 20% |
|
| INpin 6 | Connected to: Signal 60% · VBUS 40% |
|
| PADpin 7 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Soleil hardware by protolux-electronics, OBC-Flight by Kmshanley, After by DD1SB and Relay bypass by jer-lil.
The TLV76701DRVR in open source designs
The gallery holds 14 open source boards using the TLV76701DRVR from 5 GitHub repositories; a typical one measures about 180 × 140 mm and carries around 287 components.
79% are two-layer designs, the rest use four layers or more, and 93% carry an open source license.
The most starred is Soleil hardware by protolux-electronics.
Microcontrollers on boards using the TLV76701DRVR
What boards using the TLV76701DRVR are built for
TLV76701DRVR: common questions
Where can I find a TLV76701DRVR reference design?
Each of the 14 boards on this page is a real design using the TLV76701DRVR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TLV76701DRVR FB pin?
The FB pin has a resistor to GND on 5 of 5 designs, most often 200 kΩ (then 160 kΩ). Counted from the KiCad layouts of 5 open source designs using the TLV76701DRVR.
How is the TLV76701DRVR IN pin connected?
The IN pin has a capacitor to GND on 5 of 5 designs, most often 4.7 µF (then 1 µF). Counted from the KiCad layouts of 5 open source designs using the TLV76701DRVR.
How is the TLV76701DRVR OUT pin connected?
The OUT pin is tied to 6V on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the TLV76701DRVR.
Which microcontrollers do boards using the TLV76701DRVR use?
Most are built on STM32 (2), ESP32 (1) and Raspberry Pi (1).
How big is a typical board using the TLV76701DRVR?
The median is 180 × 140 mm, and 79% are two-layer designs.
What is the most popular open source board using the TLV76701DRVR?
By GitHub stars, Soleil hardware by protolux-electronics, with 22 stars.
Can I simulate one of these boards using the TLV76701DRVR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.