8 open source boards using the TPS2115APW
Real designs built with the TPS2115APW, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Renesas
Balsun
mzks
64.4 × 53.3 mm79 parts4LCC-BY-SA-4.01ESP32
Stepper synth
udu3324
266.7 × 81 mm182 parts2LGPL-3.00ESP32
Wall led matrix
richardwei6
73 × 95.9 mm91 parts2LNo license0ESP32
R2 HH Controllers
greghulette
56.6 × 111 mm122 parts4LNo license2ESP32
Body Controller V1
greghulette
123 × 78 mm94 parts4LNo license2ESP32
Body LED Controller V1
greghulette
123 × 78 mm94 parts4LNo license2ESP32
C3P0 Controller V1.1
greghulette
151.2 × 82.9 mm43 parts4LNo license2RP2040/RP2350
Peripheral board v1a
BroncoSpace-Lab
100.2 × 100.1 mm171 parts6LNo license6
How designs wire the TPS2115APW
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TPS2115APW connects to, and the resistors, capacitors and other passives placed on it.
- The IN2 pin has a capacitor to GND on 5 of 5 designs, most often 100 nF.
- The STAT pin is left unconnected on 4 of 5 designs.
- The ILIM pin has a resistor to GND on 3 of 5 designs, most often 400 Ω (then 698 Ω).
- The D0 pin is left unconnected on 3 of 5 designs (GND on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| STATpin 1 | Connected to: Not connected 80% · a signal 20% | — |
| D0pin 2 | Connected to: Not connected 60% · GND 40% | — |
| D1pin 3 | Connected to: GND 40% · 5V 20% · a signal 40% |
|
| ILIMpin 4 | Connected to: Signal 80% · not connected 20% |
|
| GNDpin 5 | Connected to: GND 100% | — |
| IN2pin 6 | Connected to: A connector 40% · VBUS 20% |
|
| OUTpin 7 | Connected to: 5V 60% · a signal 40% | — |
| IN1pin 8 | Connected to: VBUS 60% · a signal 40% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Peripheral board v1a by BroncoSpace-Lab, Body Controller V1 by greghulette, Balsun by mzks and Wall led matrix by richardwei6.
The TPS2115APW in open source designs
The gallery holds 8 open source boards using the TPS2115APW from 5 GitHub repositories; a typical one measures about 111.6 × 81.9 mm and carries around 94 components.
75% use four copper layers or more, and 25% carry an open source license.
The most starred is Peripheral board v1a by BroncoSpace-Lab.
Microcontrollers on boards using the TPS2115APW
What boards using the TPS2115APW are built for
TPS2115APW: common questions
Where can I find a TPS2115APW reference design?
Each of the 8 boards on this page is a real design using the TPS2115APW. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TPS2115APW IN2 pin connected?
The IN2 pin has a capacitor to GND on 5 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the TPS2115APW.
How is the TPS2115APW STAT pin connected?
The STAT pin is left unconnected on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the TPS2115APW.
What resistor goes on the TPS2115APW ILIM pin?
The ILIM pin has a resistor to GND on 3 of 5 designs, most often 400 Ω (then 698 Ω). Counted from the KiCad layouts of 5 open source designs using the TPS2115APW.
Which microcontrollers do boards using the TPS2115APW use?
Most are built on ESP32 (6), Renesas (1) and RP2040/RP2350 (1).
How big is a typical board using the TPS2115APW?
The median is 111.6 × 81.9 mm, and 25% are two-layer designs.
What is the most popular open source board using the TPS2115APW?
By GitHub stars, Peripheral board v1a by BroncoSpace-Lab, with 6 stars.
Can I simulate one of these boards using the TPS2115APW before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.