8 open source boards using the TPS54308

Real designs built with the TPS54308, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

8 boardsClear filters|Most starred

How designs wire the TPS54308

Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the TPS54308 connects to, and the resistors, capacitors and other passives placed on it.

  • The SW_2 pin has a series capacitor on 7 of 7 designs, most often 100 nF.
  • The SW_2 pin has a inductor on 7 of 7 designs, most often 18 µH (then 4.7 µH).
  • The BOOT_6 pin has a series capacitor on 7 of 7 designs, most often 100 nF.
  • The VIN_3 pin has a decoupling capacitor on 6 of 7 designs, most often 10 µF (then 100 nF).
GND_1pin 1Connected to: GND 86%
SW_2pin 2Connected to: Signal 100%
  • Series capacitor on 100% · 100 nF (6)
  • Inductor on 100% · 18 µH (1), 4.7 µH (1), 15 µH (1)
VIN_3pin 3Connected to: VDD_PWR 100%
  • Decoupling capacitor on 86% · 10 µF (4), 100 nF (2), 22 µF (2)
FB_4pin 4Connected to: Signal 100%
  • Resistor to GND on 86% · 13.3 kΩ (2), 48.7 kΩ (1), 22.1 kΩ (1)
  • Series resistor on 71% · 100 kΩ (4), 49.9 kΩ (1), 2 kΩ (1)
EN_5pin 5Connected to: Signal 57% · not connected 43%
  • Pull-up to VDD_PWR on 57% · 511 kΩ (2), 10 kΩ (1), 100 kΩ (1)
  • Resistor to GND on 43% · 105 kΩ (2), 33.2 kΩ (1)
BOOT_6pin 6Connected to: Signal 100%
  • Series capacitor on 100% · 100 nF (6)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Remram by hasenbanck, Benchy2 Motherboard by Daxxn, TPS5430 Buck 5V by Kraad25 and PUEE by kszygenda.

The TPS54308 in open source designs

The gallery holds 8 open source boards using the TPS54308 from 7 GitHub repositories; a typical one measures about 86 × 76.4 mm and carries around 137 components.

50% are two-layer designs, the rest use four layers or more, and 25% carry an open source license.

The most starred is Remram by hasenbanck.

Microcontrollers on boards using the TPS54308

TPS54308: common questions

Where can I find a TPS54308 reference design?

Each of the 8 boards on this page is a real design using the TPS54308. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the TPS54308 SW_2 pin connected?

The SW_2 pin has a series capacitor on 7 of 7 designs, most often 100 nF. Counted from the KiCad layouts of 7 open source designs using the TPS54308.

How is the TPS54308 BOOT_6 pin connected?

The BOOT_6 pin has a series capacitor on 7 of 7 designs, most often 100 nF. Counted from the KiCad layouts of 7 open source designs using the TPS54308.

What decoupling capacitors do designs use on the TPS54308 VIN_3 pin?

The VIN_3 pin has a decoupling capacitor on 6 of 7 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 7 open source designs using the TPS54308.

Which microcontrollers do boards using the TPS54308 use?

Most are built on STM32 (3), AVR/Arduino (1), ESP8266 (1) and RISC-V (1).

How big is a typical board using the TPS54308?

The median is 86 × 76.4 mm, and 50% are two-layer designs.

What is the most popular open source board using the TPS54308?

By GitHub stars, Remram by hasenbanck, with 40 stars.

Can I simulate one of these boards using the TPS54308 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part