7 open source boards using the TPS61022RWUR
Real designs built with the TPS61022RWUR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
SuperXBit192
kevinjuszczyk
38.1 × 50.8 mm269 parts6LGPL-3.00Tablet-Project
ShresthRao
40.3 × 155 mm115 parts4LNo license0AVR/Arduino
Otto-DIY-MUST
TUDA-MUST
58 × 54 mm76 parts4LCC-BY-SA-4.00PIC
Master
coloradocube
96 × 90 mm76 parts2LNo license0STM32
DRP.004
MuffinKing-jpeg
42 × 27 mm59 parts4LNo license0RP2040/RP2350
GYACSPEED
GodOfStrategy
81 × 57.7 mm33 parts2LNo license0ESP32
Toytalk demo v5
tomonoriyamazaki
55 × 55 mm34 parts2LNo license0
How designs wire the TPS61022RWUR
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the TPS61022RWUR connects to, and the resistors, capacitors and other passives placed on it.
- The VIN pin has a inductor on 7 of 7 designs, most often 1 µH (then 744 MH).
- The SW pin has a inductor on 6 of 7 designs, most often 1 µH (then 744 MH).
- The VOUT pin has a capacitor to GND on 6 of 7 designs, most often 22 µF (then 100 nF).
- The FB pin has a resistor to GND on 6 of 7 designs, most often 100 kΩ (then 33 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 86% | — |
| SWpin 2 | Connected to: Signal 86% |
|
| VOUTpin 3 | Connected to: Signal 57% · 5V 43% |
|
| FBpin 4 | Connected to: Signal 86% |
|
| ENpin 5 | Connected to: TPS61022RWUR 29% · BATT 43% |
|
| MODEpin 6 | Connected to: GND 43% · a signal 43% |
|
| VINpin 7 | Connected to: TPS61022RWUR 29% · BATT 29% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Master schematic by coloradocube, GYACSPEED by GodOfStrategy, SuperXBit192 by kevinjuszczyk and DRP.004 by MuffinKing-jpeg.
The TPS61022RWUR in open source designs
The gallery holds 7 open source boards using the TPS61022RWUR from 7 GitHub repositories; a typical one measures about 55 × 55 mm and carries around 76 components.
57% use four copper layers or more, and 29% carry an open source license.
The most starred is SuperXBit192 by kevinjuszczyk.
Microcontrollers on boards using the TPS61022RWUR
What boards using the TPS61022RWUR are built for
TPS61022RWUR: common questions
Where can I find a TPS61022RWUR reference design?
Each of the 7 boards on this page is a real design using the TPS61022RWUR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TPS61022RWUR VIN pin connected?
The VIN pin has a inductor on 7 of 7 designs, most often 1 µH (then 744 MH). Counted from the KiCad layouts of 7 open source designs using the TPS61022RWUR.
How is the TPS61022RWUR SW pin connected?
The SW pin has a inductor on 6 of 7 designs, most often 1 µH (then 744 MH). Counted from the KiCad layouts of 7 open source designs using the TPS61022RWUR.
How is the TPS61022RWUR VOUT pin connected?
The VOUT pin has a capacitor to GND on 6 of 7 designs, most often 22 µF (then 100 nF). Counted from the KiCad layouts of 7 open source designs using the TPS61022RWUR.
Which microcontrollers do boards using the TPS61022RWUR use?
Most are built on RP2040/RP2350 (2), AVR/Arduino (1), ESP32 (1) and PIC (1).
How big is a typical board using the TPS61022RWUR?
The median is 55 × 55 mm, and 43% are two-layer designs.
What is the most popular open source board using the TPS61022RWUR?
By GitHub stars, SuperXBit192 by kevinjuszczyk, with 0 stars.
Can I simulate one of these boards using the TPS61022RWUR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.