8 open source boards using the TPS7A3901DSCR

Real designs built with the TPS7A3901DSCR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

8 boardsClear filters|Most starred

How designs wire the TPS7A3901DSCR

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TPS7A3901DSCR connects to, and the resistors, capacitors and other passives placed on it.

  • The NR/SS pin has a capacitor to GND on 5 of 5 designs, most often 100 nF (then 10 nF).
  • The FBN pin has a series resistor on 5 of 5 designs, most often 10 kΩ (then 91 kΩ).
  • The FBP pin has a resistor to GND on 5 of 5 designs, most often 10 kΩ (then 10.2 kΩ).
  • The BUF pin has a series resistor on 4 of 5 designs, most often 10 kΩ (then 18 kΩ).
INPpin 1Connected to: V+ 80% · a signal 20%
ENpin 2Connected to: V+ 80% · a signal 20%
NR/SSpin 3Connected to: Signal 100%
  • Capacitor to GND on 100% · 100 nF (3), 10 nF (2)
GNDpin 4, 11Connected to: GND 100%
INNpin 5Connected to: -15V 60% · a signal 40%
OUTNpin 6Connected to: -5V 60% · a signal 40%
FBNpin 7Connected to: Signal 100%
  • Series resistor on 100% · 10 kΩ (3), 91 kΩ (1), 18 kΩ (1)
  • Pull-up to -5V on 60% · 42.2 kΩ (2), 100 kΩ (1)
  • Capacitor to the supply on 60% · 10 nF (3)
BUFpin 8Connected to: Signal 80% · not connected 20%
  • Series resistor on 80% · 10 kΩ (3), 18 kΩ (1)
FBPpin 9Connected to: Signal 100%
  • Resistor to GND on 100% · 10 kΩ (3), 10.2 kΩ (1), 1 kΩ (1)
  • Pull-up to 5V on 80% · 32.4 kΩ (2), 41.2 kΩ (1), 90.9 kΩ (1)
  • Capacitor to the supply on 80% · 10 nF (4)
OUTPpin 10Connected to: 5V 80% · a signal 20%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Active Scope Probe by hwidvorakinfo, Preamp by bengineer91, PANEL CARDS by k16shikano and WirelessBERA by NathansLab.

The TPS7A3901DSCR in open source designs

The gallery holds 8 open source boards using the TPS7A3901DSCR from 5 GitHub repositories; a typical one measures about 160 × 125 mm and carries around 194 components.

75% use four copper layers or more, and 0% carry an open source license.

The most starred is Active Scope Probe by hwidvorakinfo.

Parts used alongside the TPS7A3901DSCR

Microcontrollers on boards using the TPS7A3901DSCR

TPS7A3901DSCR: common questions

Where can I find a TPS7A3901DSCR reference design?

Each of the 8 boards on this page is a real design using the TPS7A3901DSCR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the TPS7A3901DSCR NR/SS pin connected?

The NR/SS pin has a capacitor to GND on 5 of 5 designs, most often 100 nF (then 10 nF). Counted from the KiCad layouts of 5 open source designs using the TPS7A3901DSCR.

What resistor goes on the TPS7A3901DSCR FBN pin?

The FBN pin has a series resistor on 5 of 5 designs, most often 10 kΩ (then 91 kΩ). Counted from the KiCad layouts of 5 open source designs using the TPS7A3901DSCR.

What resistor goes on the TPS7A3901DSCR FBP pin?

The FBP pin has a resistor to GND on 5 of 5 designs, most often 10 kΩ (then 10.2 kΩ). Counted from the KiCad layouts of 5 open source designs using the TPS7A3901DSCR.

Which microcontrollers do boards using the TPS7A3901DSCR use?

Most are built on Microchip SAM (2) and ESP32 (1).

How big is a typical board using the TPS7A3901DSCR?

The median is 160 × 125 mm, and 25% are two-layer designs.

What is the most popular open source board using the TPS7A3901DSCR?

By GitHub stars, Active Scope Probe by hwidvorakinfo, with 21 stars.

Can I simulate one of these boards using the TPS7A3901DSCR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part