9 open source boards using the 93CxxC
Real designs built with the 93CxxC, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
Gecko5education
logisim-evolution
60.6 × 100 mm308 parts6LMIT18RP2040/RP2350
PCE colorlight carrier
supermomo31
180 × 160 mm253 parts4LNo license0FPGA
USIC
dabridgham
214.1 × 265.6 mm245 parts6LNo license0ESP32
MR SLDR
MikolajMarkiel
89.3 × 68 mm135 parts2LMIT0AVR/Arduino
M68k hbc
ehbc-project
304.8 × 243.8 mm72 parts6LNo license0FPGA
FD new testblock2
Jegeva
100 × 139 mm273 parts1LNo license0FPGA
FD2
Jegeva
112 × 158 mm263 parts4LNo license0FPGA
FD3
Jegeva
112 × 158 mm259 parts4LNo license0FPGA
FD-TUNEDDDR+TERM@x+500
Jegeva
112 × 158 mm239 parts1LNo license0
How designs wire the 93CxxC
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the 93CxxC connects to, and the resistors, capacitors and other passives placed on it.
- The ORG pin is tied to 3.3V on 5 of 6 designs.
- The CS pin has a pull-up to 3.3V on 4 of 6 designs, most often 10 kΩ.
- The SCLK pin has a pull-up to 3.3V on 4 of 6 designs, most often 10 kΩ.
- The DI pin has a series resistor on 4 of 6 designs, most often 2.2 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CSpin 1 | Connected to: FT2232HQ 50% |
|
| SCLKpin 2 | Connected to: FT2232HQ 50% |
|
| DIpin 3 | Connected to: FT2232HQ 50% |
|
| DOpin 4 | Connected to: Signal 100% |
|
| GNDpin 5 | Connected to: GND 100% | — |
| ORGpin 6 | Connected to: 3.3V 83% · a signal 17% | — |
| NCpin 7 | Connected to: Not connected 100% | — |
| VCCpin 8 | Connected to: 3.3V 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Gecko5education by logisim-evolution, USIC by dabridgham, M68k hbc by ehbc-project and FD new testblock2 by Jegeva.
The 93CxxC in open source designs
The gallery holds 9 open source boards using the 93CxxC from 6 GitHub repositories; a typical one measures about 112 × 158 mm and carries around 253 components.
67% use four copper layers or more, and 22% carry an open source license.
The most starred is Gecko5education by logisim-evolution.
Parts used alongside the 93CxxC
Microcontrollers on boards using the 93CxxC
What boards using the 93CxxC are built for
93CxxC: common questions
Where can I find a 93CxxC reference design?
Each of the 9 boards on this page is a real design using the 93CxxC. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the 93CxxC ORG pin connected?
The ORG pin is tied to 3.3V on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the 93CxxC.
What pull-up resistor is used on the 93CxxC CS pin?
The CS pin has a pull-up to 3.3V on 4 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the 93CxxC.
What pull-up resistor is used on the 93CxxC SCLK pin?
The SCLK pin has a pull-up to 3.3V on 4 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the 93CxxC.
Which microcontrollers do boards using the 93CxxC use?
Most are built on FPGA (6), AVR/Arduino (1), ESP32 (1) and RP2040/RP2350 (1).
How big is a typical board using the 93CxxC?
The median is 112 × 158 mm, and 33% are two-layer designs.
What is the most popular open source board using the 93CxxC?
By GitHub stars, Gecko5education by logisim-evolution, with 18 stars.
Can I simulate one of these boards using the 93CxxC before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.