6 open source boards using the 93LC46BT-I/OT
Real designs built with the 93LC46BT-I/OT, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Zs1100a
zscircuits
129 × 104.6 mm486 partsNo license76FPGA
ICE40-fpga
joshajohnson
50 × 22.9 mm62 parts2LCC-BY-NC-4.026FPGA
Open-TWIST rev0
louisreg
186 × 160 mm805 parts6LNo license0FPGA
Radarriset
faoziaziz
89.2 × 62.4 mm124 parts2LNo license0- schematic only · 89 parts
Tigard
mukkasrikanth
89 partsNo license0 FPGA
ICEBreaker+++
gregdavill
56 × 37 mm104 parts4LNo license178
How designs wire the 93LC46BT-I/OT
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the 93LC46BT-I/OT connects to, and the resistors, capacitors and other passives placed on it.
- The DO pin has a series resistor on 4 of 5 designs, most often 2.2 kΩ (then 2 kΩ).
- The DI pin has a series resistor on 4 of 5 designs, most often 2.2 kΩ (then 2 kΩ).
- The VCC pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF.
- The CLK pin has a series resistor on 2 of 5 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| DOpin 1 | Connected to: Signal 80% · 3.3V 20% |
|
| VSSpin 2 | Connected to: GND 80% · a signal 20% | — |
| DIpin 3 | Connected to: Signal 100% |
|
| CLKpin 4 | Connected to: Signal 100% |
|
| CSpin 5 | Connected to: Signal 80% · 1.2V 20% |
|
| VCCpin 6 | Connected to: 3.3V 60% · a signal 40% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ICEBreaker+++ by gregdavill, Zs1100a by zscircuits, ICE40-fpga by joshajohnson and Radarriset by faoziaziz.
The 93LC46BT-I/OT in open source designs
The gallery holds 6 open source boards using the 93LC46BT-I/OT from 6 GitHub repositories; a typical one measures about 89.2 × 62.4 mm and carries around 114 components.
50% are two-layer designs, the rest use four layers or more, and 0% carry an open source license.
The most starred is ICEBreaker+++ by gregdavill.
Parts used alongside the 93LC46BT-I/OT
Microcontrollers on boards using the 93LC46BT-I/OT
What boards using the 93LC46BT-I/OT are built for
93LC46BT-I/OT: common questions
Where can I find a 93LC46BT-I/OT reference design?
Each of the 6 boards on this page is a real design using the 93LC46BT-I/OT. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the 93LC46BT-I/OT DO pin?
The DO pin has a series resistor on 4 of 5 designs, most often 2.2 kΩ (then 2 kΩ). Counted from the KiCad layouts of 5 open source designs using the 93LC46BT-I/OT.
What resistor goes on the 93LC46BT-I/OT DI pin?
The DI pin has a series resistor on 4 of 5 designs, most often 2.2 kΩ (then 2 kΩ). Counted from the KiCad layouts of 5 open source designs using the 93LC46BT-I/OT.
What decoupling capacitors do designs use on the 93LC46BT-I/OT VCC pin?
The VCC pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the 93LC46BT-I/OT.
Which microcontrollers do boards using the 93LC46BT-I/OT use?
Most are built on FPGA (4).
How big is a typical board using the 93LC46BT-I/OT?
The median is 89.2 × 62.4 mm, and 50% are two-layer designs.
What is the most popular open source board using the 93LC46BT-I/OT?
By GitHub stars, ICEBreaker+++ by gregdavill, with 178 stars.
Can I simulate one of these boards using the 93LC46BT-I/OT before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.