7 open source boards using the ACS712ELCTR-05B-T
Real designs built with the ACS712ELCTR-05B-T, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
PaneledKit
williamthayer
93.6 × 94.4 mm226 parts2LNo license1STM32
Belegt
eurovibes
60 × 145 mm120 parts4LCERN-OHL-S-2.00AVR/Arduino
Multimetre
hilham1990
70 × 120 mm82 parts2LCC-BY-NC-4.00ESP32
Smart home
vishal007-hacker
200 × 100 mm76 parts2LMIT0PaneledKitDNP Variant 4-15
williamthayer
93.6 × 94.4 mm197 parts2LNo license1AVR/Arduino
Solar Power Monitoring System
ysaip07
125.7 × 103 mm14 parts2LNo license0Daisy Board Servo
williamthayer
29.8 × 46.2 mm56 parts2LNo license1
How designs wire the ACS712ELCTR-05B-T
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the ACS712ELCTR-05B-T connects to, and the resistors, capacitors and other passives placed on it.
- The FILTER pin has a capacitor to GND on 4 of 5 designs, most often 100 nF (then 1 nF).
- The VIOUT pin has a series resistor on 3 of 5 designs, most often 2.2 kΩ (then 2 kΩ).
- The VCC pin has a decoupling capacitor on 2 of 5 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 5 | Connected to: GND 100% | — |
| FILTERpin 6 | Connected to: Signal 80% · not connected 20% |
|
| VIOUTpin 7 | Connected to: Signal 100% |
|
| VCCpin 8 | Connected to: 5V 100% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Daisy Board Servo by williamthayer, Belegt by eurovibes, Multimetre by hilham1990 and Smart home by vishal007-hacker.
The ACS712ELCTR-05B-T in open source designs
The gallery holds 7 open source boards using the ACS712ELCTR-05B-T from 5 GitHub repositories; a typical one measures about 93.6 × 100 mm and carries around 82 components.
86% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.
The most starred is PaneledKit by williamthayer.
Parts used alongside the ACS712ELCTR-05B-T
Microcontrollers on boards using the ACS712ELCTR-05B-T
What boards using the ACS712ELCTR-05B-T are built for
ACS712ELCTR-05B-T: common questions
Where can I find a ACS712ELCTR-05B-T reference design?
Each of the 7 boards on this page is a real design using the ACS712ELCTR-05B-T. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ACS712ELCTR-05B-T FILTER pin connected?
The FILTER pin has a capacitor to GND on 4 of 5 designs, most often 100 nF (then 1 nF). Counted from the KiCad layouts of 5 open source designs using the ACS712ELCTR-05B-T.
What resistor goes on the ACS712ELCTR-05B-T VIOUT pin?
The VIOUT pin has a series resistor on 3 of 5 designs, most often 2.2 kΩ (then 2 kΩ). Counted from the KiCad layouts of 5 open source designs using the ACS712ELCTR-05B-T.
What decoupling capacitors do designs use on the ACS712ELCTR-05B-T VCC pin?
The VCC pin has a decoupling capacitor on 2 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the ACS712ELCTR-05B-T.
Which microcontrollers do boards using the ACS712ELCTR-05B-T use?
Most are built on AVR/Arduino (2), ESP32 (1) and STM32 (1).
How big is a typical board using the ACS712ELCTR-05B-T?
The median is 93.6 × 100 mm, and 86% are two-layer designs.
What is the most popular open source board using the ACS712ELCTR-05B-T?
By GitHub stars, PaneledKit by williamthayer, with 1 stars.
Can I simulate one of these boards using the ACS712ELCTR-05B-T before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.