11 open source boards using the AD8232ACPZ-R7
Real designs built with the AD8232ACPZ-R7, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Nervous-ECG
sensors-inl
26 × 40 mm60 parts2LMIT2Stamp-Board of-AD8232
nwasr
17.5 × 24.7 mm23 parts2LMIT2STM32
HM-Collector-Rev2
konstantinosfragkoulis
37.5 × 29.5 mm87 parts4LMIT1SparkFun-AD8232-Replica
nwasr
27.9 × 37.6 mm30 parts2LMIT1ESP32
Emg custom
rastorc3v
56.2 × 51.1 mm104 parts2LNo license0ECG-Monitor-AD8232
Giancarlo0811
33 × 57.2 mm49 parts2LNo license0Single-Lead-ECG-Shield
ADITHYANWUU2
68.6 × 53.4 mm14 parts2LMIT0ECG-Biosensor-AD8232-final
shrimaan-rapuru
140 × 56.5 mm8 parts2LMIT0STM32
HM-Rev1
konstantinosfragkoulis
44 × 27.2 mm83 parts4LMIT1ECG-Biosensor-AD8232
shrimaan-rapuru
80 × 50 mm7 parts2LMIT0ECG-Biosensor-AD8232-fixed
shrimaan-rapuru
20.5 × 20 mm7 parts2LMIT0
How designs wire the AD8232ACPZ-R7
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the AD8232ACPZ-R7 connects to, and the resistors, capacitors and other passives placed on it.
- The -IN pin has a series resistor on 7 of 8 designs, most often 180 kΩ.
- The OPAMP+ pin has a series capacitor on 7 of 8 designs, most often 10 nF (then 6.8 nF).
- The OPAMP+ pin has a series resistor on 7 of 8 designs, most often 1 MΩ (then 100 kΩ).
- The OUT pin has a series resistor on 7 of 8 designs, most often 1 MΩ (then 1 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| HPDRIVEpin 1 | Connected to: Signal 75% · not connected 25% |
|
| +INpin 2 | Connected to: Signal 88% |
|
| -INpin 3 | Connected to: Signal 100% |
|
| RLDFBpin 4 | Connected to: Signal 100% |
|
| RLDpin 5 | Connected to: Signal 100% |
|
| SWpin 6 | Connected to: Signal 75% · not connected 25% |
|
| OPAMP+pin 7 | Connected to: Signal 88% |
|
| REFOUTpin 8 | Connected to: Signal 88% |
|
| OPAMP-pin 9 | Connected to: Signal 75% · not connected 25% |
|
| OUTpin 10 | Connected to: A connector 50% |
|
| SDNpin 13 | Connected to: A connector 50% |
|
| AC/DCpin 14 | Connected to: GND 88% | — |
| FRpin 15 | Connected to: VCC 63% | — |
| GND_1pin 16 | Connected to: GND 88% | — |
| +VSpin 17 | Connected to: 3.3V 88% | — |
| REFINpin 18 | Connected to: Signal 75% |
|
| IAOUTpin 19 | Connected to: Signal 88% |
|
| HPSENSEpin 20 | Connected to: Signal 75% |
|
| GND_2pin 21 | Connected to: GND 86% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Stamp-Board of-AD8232 by nwasr, Nervous-ECG by sensors-inl, HM-Collector-Rev2 by konstantinosfragkoulis and SparkFun-AD8232-Replica by nwasr.
The AD8232ACPZ-R7 in open source designs
The gallery holds 11 open source boards using the AD8232ACPZ-R7 from 8 GitHub repositories; a typical one measures about 37.5 × 40 mm and carries around 30 components.
82% are two-layer designs, the rest use four layers or more, and 82% carry an open source license.
The most starred is Nervous-ECG by sensors-inl.
What boards using the AD8232ACPZ-R7 are built for
AD8232ACPZ-R7: common questions
Where can I find a AD8232ACPZ-R7 reference design?
Each of the 11 boards on this page is a real design using the AD8232ACPZ-R7. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the AD8232ACPZ-R7 -IN pin?
The -IN pin has a series resistor on 7 of 8 designs, most often 180 kΩ. Counted from the KiCad layouts of 8 open source designs using the AD8232ACPZ-R7.
How is the AD8232ACPZ-R7 OPAMP+ pin connected?
The OPAMP+ pin has a series capacitor on 7 of 8 designs, most often 10 nF (then 6.8 nF). Counted from the KiCad layouts of 8 open source designs using the AD8232ACPZ-R7.
What resistor goes on the AD8232ACPZ-R7 OUT pin?
The OUT pin has a series resistor on 7 of 8 designs, most often 1 MΩ (then 1 kΩ). Counted from the KiCad layouts of 8 open source designs using the AD8232ACPZ-R7.
Which microcontrollers do boards using the AD8232ACPZ-R7 use?
Most are built on STM32 (2) and ESP32 (1).
How big is a typical board using the AD8232ACPZ-R7?
The median is 37.5 × 40 mm, and 82% are two-layer designs.
What is the most popular open source board using the AD8232ACPZ-R7?
By GitHub stars, Nervous-ECG by sensors-inl, with 2 stars.
Can I simulate one of these boards using the AD8232ACPZ-R7 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.