6 open source boards using the AP62300WU-7
Real designs built with the AP62300WU-7, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
PCBGolf
commaai
67.2 × 64.4 mm238 parts2LNo license59ESP8266
Seatalk wifi
atonizzo
31 × 22 mm32 parts2LApache-2.012STM32
PCBGolf
ulyssecrn
33.9 × 42.3 mm253 parts4LNo license0STM32
Challenge
FAliIAM
67.2 × 64.4 mm238 parts2LNo license0AI Design Generation
flannellab
175 × 105 mm48 parts2LNo license0STM32
Pcbgolf
chilly23
67.2 × 64.4 mm238 parts2LMIT0
How designs wire the AP62300WU-7
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the AP62300WU-7 connects to, and the resistors, capacitors and other passives placed on it.
- The EN_5 pin has a pull-up to 5V on 6 of 6 designs, most often 10 kΩ (then 316 kΩ).
- The BST_6 pin has a series capacitor on 6 of 6 designs, most often 100 nF.
- The SW_2 pin has a inductor on 5 of 6 designs, most often 3.3 µH.
- The SW_2 pin has a series capacitor on 5 of 6 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GND_1pin 1 | Connected to: GND 83% · 5V 17% | — |
| SW_2pin 2 | Connected to: Signal 83% · 5V 17% |
|
| IN_3pin 3 | Connected to: 5V 83% · GND 17% | — |
| FB_4pin 4 | Connected to: Signal 100% |
|
| EN_5pin 5 | Connected to: Signal 100% |
|
| BST_6pin 6 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PCBGolf by commaai, Seatalk wifi by atonizzo, Pcbgolf by chilly23 and Challenge by FAliIAM.
The AP62300WU-7 in open source designs
The gallery holds 6 open source boards using the AP62300WU-7 from 6 GitHub repositories; a typical one measures about 67.2 × 64.4 mm and carries around 238 components.
83% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.
The most starred is PCBGolf by commaai.
Parts used alongside the AP62300WU-7
What boards using the AP62300WU-7 are built for
AP62300WU-7: common questions
Where can I find a AP62300WU-7 reference design?
Each of the 6 boards on this page is a real design using the AP62300WU-7. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the AP62300WU-7 EN_5 pin?
The EN_5 pin has a pull-up to 5V on 6 of 6 designs, most often 10 kΩ (then 316 kΩ). Counted from the KiCad layouts of 6 open source designs using the AP62300WU-7.
How is the AP62300WU-7 BST_6 pin connected?
The BST_6 pin has a series capacitor on 6 of 6 designs, most often 100 nF. Counted from the KiCad layouts of 6 open source designs using the AP62300WU-7.
How is the AP62300WU-7 SW_2 pin connected?
The SW_2 pin has a inductor on 5 of 6 designs, most often 3.3 µH. Counted from the KiCad layouts of 6 open source designs using the AP62300WU-7.
What parts are used alongside the AP62300WU-7?
The MCP2542FDT-H/MNY, TPS25944ARVCR, USB2517, STM32H725ZGT and NCS20071SN2T1G appear in the most repositories here.
Which microcontrollers do boards using the AP62300WU-7 use?
Most are built on STM32 (4) and ESP8266 (1).
How big is a typical board using the AP62300WU-7?
The median is 67.2 × 64.4 mm, and 83% are two-layer designs.
What is the most popular open source board using the AP62300WU-7?
By GitHub stars, PCBGolf by commaai, with 59 stars.
Can I simulate one of these boards using the AP62300WU-7 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.