8 open source boards using the USB2517
Real designs built with the USB2517, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
PCBGolf
commaai
67.2 × 64.4 mm238 parts2LNo license59STM32
PCBGolf
ulyssecrn
33.9 × 42.3 mm253 parts4LNo license0STM32
Submission
chilly23
35 × 65 mm243 parts4LMIT0STM32
Challenge
FAliIAM
67.2 × 64.4 mm238 parts2LNo license0Raspberry Pi
Kicad hiltop 63hp backplane
devtank-ltd
200 × 129 mm161 parts6LCERN-OHL-W-2.00Hub
komori-t
46.5 × 34 mm34 parts2LNo license8STM32
Submission with nets
chilly23
35 × 65 mm243 parts4LMIT0STM32
Pcbgolf
chilly23
67.2 × 64.4 mm238 parts2LMIT0
How designs wire the USB2517
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the USB2517 connects to, and the resistors, capacitors and other passives placed on it.
- The VDD18_25 pin has a capacitor to GND on 6 of 6 designs, most often 100 nF (then 10 µF).
- The XTAL1_61 pin has a crystal on 6 of 6 designs, most often 24 MHz.
- The VDD18PLL_62 pin has a capacitor to GND on 6 of 6 designs, most often 100 nF (then 10 µF).
- The RBIAS_63 pin has a resistor to GND on 6 of 6 designs, most often 12 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDA33_5pin 5 | Connected to: 3.3V 100% |
|
| VDDA33_10pin 10 | Connected to: 3.3V 100% |
|
| USBDN5_DM_11pin 11 | Connected to: Not connected 83% · a signal 17% | — |
| USBDN5_DP_12pin 12 | Connected to: Not connected 83% · a signal 17% | — |
| CFG_SEL2_13pin 13 | Connected to: 3.3V 67% · a signal 33% | — |
| LED_B7_N_14pin 14 | Connected to: Not connected 83% · a signal 17% | — |
| LED_A7_N_15pin 15 | Connected to: Not connected 83% · a signal 17% | — |
| LED_B6_N_16pin 16 | Connected to: Not connected 83% · a signal 17% | — |
| LED_A6_N_17pin 17 | Connected to: Not connected 83% · a signal 17% | — |
| LED_B5_N_18pin 18 | Connected to: Not connected 83% · a signal 17% | — |
| TEST_19pin 19 | Connected to: GND 83% · not connected 17% | — |
| PRTPWR4_20pin 20 | Connected to: Not connected 100% | — |
| OCS4_N_21pin 21 | Connected to: Not connected 100% | — |
| OCS3_N_22pin 22 | Connected to: Not connected 100% | — |
| PRTPWR3_23pin 23 | Connected to: Not connected 100% | — |
| VDD33CR_24pin 24 | Connected to: 3.3V 100% |
|
| VDD18_25pin 25 | Connected to: Signal 100% |
|
| PRTPWR2_26pin 26 | Connected to: Not connected 100% | — |
| OCS2_N_27pin 27 | Connected to: Not connected 100% | — |
| OCS1_N_28pin 28 | Connected to: Not connected 100% | — |
| PRTPWR1_29pin 29 | Connected to: Not connected 100% | — |
| PRTPWR5_30pin 30 | Connected to: Not connected 100% | — |
| LED_A5_N_31pin 31 | Connected to: Not connected 83% · a signal 17% | — |
| LED_B4_N_32pin 32 | Connected to: Not connected 83% · a signal 17% | — |
| LED_A4_N_33pin 33 | Connected to: Not connected 83% · a signal 17% | — |
| LED_B3_N_34pin 34 | Connected to: Not connected 83% · a signal 17% | — |
| OCS5_N_35pin 35 | Connected to: Not connected 100% | — |
| PRTPWR7_36pin 36 | Connected to: Not connected 100% | — |
| OCS7_N_37pin 37 | Connected to: Not connected 100% | — |
| OCS6_N_38pin 38 | Connected to: Not connected 100% | — |
| PRTPWR6_39pin 39 | Connected to: Not connected 100% | — |
| SDA_40pin 40 | Connected to: The microcontroller 67% · not connected 17% |
|
| SCL_41pin 41 | Connected to: The microcontroller 67% |
|
| CFG_SEL1_42pin 42 | Connected to: 3.3V 67% · a signal 33% | — |
| RESET_N_43pin 43 | Connected to: 3.3V 67% · a signal 33% | — |
| VBUS_DET_44pin 44 | Connected to: Signal 83% · 3.3V 17% |
|
| SUSP_IND_45pin 45 | Connected to: Signal 100% |
|
| VDD33_46pin 46 | Connected to: 3.3V 100% |
|
| LED_A3_N_47pin 47 | Connected to: Not connected 83% · a signal 17% | — |
| LED_B2_N_48pin 48 | Connected to: Not connected 83% · a signal 17% | — |
26 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PCBGolf by commaai, Hub by komori-t, Pcbgolf by chilly23 and Kicad hiltop 63hp backplane by devtank-ltd.
The USB2517 in open source designs
The gallery holds 8 open source boards using the USB2517 from 6 GitHub repositories; a typical one measures about 56.9 × 64.4 mm and carries around 238 components.
50% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is PCBGolf by commaai.
Parts used alongside the USB2517
Microcontrollers on boards using the USB2517
What boards using the USB2517 are built for
USB2517: common questions
Where can I find a USB2517 reference design?
Each of the 8 boards on this page is a real design using the USB2517. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the USB2517 VDD18_25 pin connected?
The VDD18_25 pin has a capacitor to GND on 6 of 6 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 6 open source designs using the USB2517.
How is the USB2517 XTAL1_61 pin connected?
The XTAL1_61 pin has a crystal on 6 of 6 designs, most often 24 MHz. Counted from the KiCad layouts of 6 open source designs using the USB2517.
How is the USB2517 VDD18PLL_62 pin connected?
The VDD18PLL_62 pin has a capacitor to GND on 6 of 6 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 6 open source designs using the USB2517.
What parts are used alongside the USB2517?
The AP62300WU-7, MCP2542FDT-H/MNY, TPS25944ARVCR, STM32H725ZGT and NCS20071SN2T1G appear in the most repositories here.
Which microcontrollers do boards using the USB2517 use?
Most are built on STM32 (6) and Raspberry Pi (1).
How big is a typical board using the USB2517?
The median is 56.9 × 64.4 mm, and 50% are two-layer designs.
What is the most popular open source board using the USB2517?
By GitHub stars, PCBGolf by commaai, with 59 stars.
Can I simulate one of these boards using the USB2517 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.