7 open source boards using the Arduino_Uno_R3_Shield

Real designs built with the Arduino_Uno_R3_Shield, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

7 boardsClear filters|Most starred

How designs wire the Arduino_Uno_R3_Shield

Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the Arduino_Uno_R3_Shield connects to, and the resistors, capacitors and other passives placed on it.

  • The IOREF pins is left unconnected on 7 of 7 designs.
  • The RESET pins is left unconnected on 7 of 7 designs.
  • The VIN pins is left unconnected on 6 of 7 designs.
  • The A1 pins is left unconnected on 6 of 7 designs.
NCpin 1Connected to: Not connected 100%
IOREFpin 2, IORFConnected to: Not connected 100%
RESETpin 3, RST1Connected to: Not connected 100%
3.3Vpin 3V3Connected to: Not connected 100%
3V3pin 4Connected to: Not connected 67% · VDD 33%
+5Vpin 5Connected to: Not connected 67% · VCC 33%
SPI_5Vpin 5V2Connected to: Not connected 100%
GNDpin 6, 7, 29, GND1, GND2, GND3Connected to: GND 81% · not connected 19%
VINpin 8, VINConnected to: Not connected 86%
A0pin 9, A0Connected to: Not connected 71% · a signal 29%
A1pin 10, A1Connected to: Not connected 86%
A2pin 11, A2Connected to: Not connected 71% · a signal 29%
A3pin 12, A3Connected to: Not connected 86%
SDA/A4pin 13, 31Connected to: Not connected 100%
SCL/A5pin 14, 32Connected to: Not connected 100%
D0/RXpin 15, D0Connected to: Not connected 71% · a signal 29%
D2pin 17Connected to: Signal 67% · not connected 33%
  • Series resistor on 67% · 10 kΩ (2)
D3pin 18Connected to: Signal 67% · not connected 33%
  • Series resistor on 67% · 10 kΩ (2)
D5pin 20, D5Connected to: Signal 71% · not connected 29%
  • Series resistor on 43% · 10 kΩ (2), 470 Ω (1)
D6pin 21, D6Connected to: Signal 71% · not connected 29%
  • Series resistor on 43% · 10 kΩ (2), 470 Ω (1)
D7pin 22, D7Connected to: Signal 86%
  • Series resistor on 43% · 10 kΩ (2), 470 Ω (1)
D9pin 24, D9Connected to: Signal 71% · not connected 29%
  • Series resistor on 43% · 10 kΩ (2), 470 Ω (1)
D10pin 25Connected to: Signal 67% · not connected 33%
  • Series resistor on 67% · 10 kΩ (2)
D13pin 28, D13Connected to: Not connected 71% · a signal 29%
AREFpin 30, AREFConnected to: Not connected 86%
A4pin A4Connected to: Not connected 75% · a signal 25%
A5pin A5Connected to: Not connected 75% · a signal 25%
SPI_GNDpin GND4Connected to: Not connected 75% · GND 25%
SPI_RESETpin RST2Connected to: Not connected 75% · a signal 25%

14 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Oxygen concentrator by RepRapLtd, RP2040-PinTest by red-scorp, Final pcb by cshieldsce and Audio shield by deniskokarev.

The Arduino_Uno_R3_Shield in open source designs

The gallery holds 7 open source boards using the Arduino_Uno_R3_Shield from 7 GitHub repositories; a typical one measures about 68.6 × 53.6 mm and carries around 20 components.

100% are two-layer designs, the rest use four layers or more, and 57% carry an open source license.

The most starred is Oxygen concentrator by RepRapLtd.

Microcontrollers on boards using the Arduino_Uno_R3_Shield

What boards using the Arduino_Uno_R3_Shield are built for

Arduino_Uno_R3_Shield: common questions

Where can I find a Arduino_Uno_R3_Shield reference design?

Each of the 7 boards on this page is a real design using the Arduino_Uno_R3_Shield. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the Arduino_Uno_R3_Shield IOREF pin connected?

The IOREF pins is left unconnected on 7 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the Arduino_Uno_R3_Shield.

How is the Arduino_Uno_R3_Shield RESET pin connected?

The RESET pins is left unconnected on 7 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the Arduino_Uno_R3_Shield.

How is the Arduino_Uno_R3_Shield VIN pin connected?

The VIN pins is left unconnected on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the Arduino_Uno_R3_Shield.

Which microcontrollers do boards using the Arduino_Uno_R3_Shield use?

Most are built on AVR/Arduino (7).

How big is a typical board using the Arduino_Uno_R3_Shield?

The median is 68.6 × 53.6 mm, and 100% are two-layer designs.

What is the most popular open source board using the Arduino_Uno_R3_Shield?

By GitHub stars, Oxygen concentrator by RepRapLtd, with 83 stars.

Can I simulate one of these boards using the Arduino_Uno_R3_Shield before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part