6 open source boards using the ATmega88PA-AU
Real designs built with the ATmega88PA-AU, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
SwinsidNeat
jsanpe
17.5 × 36.6 mm13 parts2LMIT16AVR/Arduino
Esr meter
vpatkov
66 × 99.1 mm101 parts2LNo license5AVR/Arduino
NanoSwinSidC
UzixLS
35.8 × 17.5 mm15 parts2LMIT2AVR/Arduino
LEC008011---Module sonore pour sons d ambiance
LECTIX
53 × 53 mm36 parts2LCERN-OHL-S-2.01AVR/Arduino
ZXSwinSID
schenkmi
78.4 × 49.9 mm69 parts2LGPL-3.00AVR/Arduino
NanoSwinSIDlives
jimbro1000
18 × 38.3 mm14 parts2LCERN-OHL-P-2.00
How designs wire the ATmega88PA-AU
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ATmega88PA-AU connects to, and the resistors, capacitors and other passives placed on it.
- The PB1 pin has a series resistor on 5 of 6 designs, most often 1 kΩ (then 2.4 kΩ).
- The ADC6 pin is left unconnected on 6 of 6 designs.
- The XTAL2/PB7 pin is left unconnected on 5 of 6 designs.
- The ADC7 pin is left unconnected on 5 of 6 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 3, 5, 21 | Connected to: GND 94% | — |
| VCCpin 4, 6 | Connected to: 5V 92% |
|
| XTAL1/PB6pin 7 | Connected to: Signal 83% · not connected 17% |
|
| XTAL2/PB7pin 8 | Connected to: Not connected 83% · a signal 17% | — |
| PB1pin 13 | Connected to: Signal 100% |
|
| PB2pin 14 | Connected to: Signal 100% |
|
| AVCCpin 18 | Connected to: 5V 100% | — |
| ADC6pin 19 | Connected to: Not connected 100% | — |
| AREFpin 20 | Connected to: Not connected 67% · a signal 33% |
|
| ADC7pin 22 | Connected to: Not connected 83% · a signal 17% | — |
| RESET/PC6pin 29 | Connected to: A connector 83% |
|
| PD1pin 31 | Connected to: A connector 33% |
|
17 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include SwinsidNeat by jsanpe, Esr meter by vpatkov, NanoSwinSidC by UzixLS and LEC008011---Module sonore pour sons d ambiance by LECTIX.
The ATmega88PA-AU in open source designs
The gallery holds 6 open source boards using the ATmega88PA-AU from 6 GitHub repositories; a typical one measures about 44.4 × 44.1 mm and carries around 26 components.
100% are two-layer designs, the rest use four layers or more, and 83% carry an open source license.
The most starred is SwinsidNeat by jsanpe.
Microcontrollers on boards using the ATmega88PA-AU
What boards using the ATmega88PA-AU are built for
ATmega88PA-AU: common questions
Where can I find a ATmega88PA-AU reference design?
Each of the 6 boards on this page is a real design using the ATmega88PA-AU. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the ATmega88PA-AU PB1 pin?
The PB1 pin has a series resistor on 5 of 6 designs, most often 1 kΩ (then 2.4 kΩ). Counted from the KiCad layouts of 6 open source designs using the ATmega88PA-AU.
How is the ATmega88PA-AU ADC6 pin connected?
The ADC6 pin is left unconnected on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the ATmega88PA-AU.
How is the ATmega88PA-AU XTAL2/PB7 pin connected?
The XTAL2/PB7 pin is left unconnected on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the ATmega88PA-AU.
Which microcontrollers do boards using the ATmega88PA-AU use?
Most are built on AVR/Arduino (6).
How big is a typical board using the ATmega88PA-AU?
The median is 44.4 × 44.1 mm, and 100% are two-layer designs.
What is the most popular open source board using the ATmega88PA-AU?
By GitHub stars, SwinsidNeat by jsanpe, with 16 stars.
Can I simulate one of these boards using the ATmega88PA-AU before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.