5 open source boards using the ATtiny85V-10S
Real designs built with the ATtiny85V-10S, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Sgb mbc5 1-4
MouseBiteLabs
110.7 × 69.8 mm88 parts4LCC-BY-SA-4.040AVR/Arduino
Ws 3.0
boanjo
72.7 × 114 mm53 parts2LNo license4AVR/Arduino
LumiGuard-Intelligent-Dual-UV-White-Control-System
IsmelArab
50 × 50 mm35 parts2LApache-2.00AVR/Arduino
Attiny85 NFC MULTI TAG
dgm91-pro
35 × 62 mm15 parts2LNo license0AVR/Arduino
IRS
Lee34667
79 × 78 mm23 parts2LNo license1
How designs wire the ATtiny85V-10S
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the ATtiny85V-10S connects to, and the resistors, capacitors and other passives placed on it.
- The XTAL1/PB3 pin has a series resistor on 4 of 5 designs, most often 4.7 kΩ (then 47 Ω).
- The XTAL2/PB4 pin has a series resistor on 4 of 5 designs, most often 4.7 kΩ (then 47 Ω).
- The VCC pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 1 µF).
- The RESET/PB5 pin has a pull-up to 5V on 3 of 5 designs, most often 10 kΩ (then 4.7 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| RESET/PB5pin 1 | Connected to: A connector 80% |
|
| XTAL1/PB3pin 2 | Connected to: Signal 100% |
|
| XTAL2/PB4pin 3 | Connected to: Signal 100% |
|
| GNDpin 4 | Connected to: GND 100% | — |
| AREF/PB0pin 5 | Connected to: A connector 80% |
|
| PB1pin 6 | Connected to: A connector 80% |
|
| PB2pin 7 | Connected to: A connector 80% |
|
| VCCpin 8 | Connected to: 5V 60% · a signal 40% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Sgb mbc5 1-4 by MouseBiteLabs, Ws 3.0 by boanjo, IRS by Lee34667 and Attiny85 NFC MULTI TAG by dgm91-pro.
The ATtiny85V-10S in open source designs
The gallery holds 5 open source boards using the ATtiny85V-10S from 5 GitHub repositories; a typical one measures about 72.7 × 69.8 mm and carries around 35 components.
80% are two-layer designs, the rest use four layers or more, and 40% carry an open source license.
The most starred is Sgb mbc5 1-4 by MouseBiteLabs.
Microcontrollers on boards using the ATtiny85V-10S
What boards using the ATtiny85V-10S are built for
ATtiny85V-10S: common questions
Where can I find a ATtiny85V-10S reference design?
Each of the 5 boards on this page is a real design using the ATtiny85V-10S. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the ATtiny85V-10S XTAL1/PB3 pin?
The XTAL1/PB3 pin has a series resistor on 4 of 5 designs, most often 4.7 kΩ (then 47 Ω). Counted from the KiCad layouts of 5 open source designs using the ATtiny85V-10S.
What resistor goes on the ATtiny85V-10S XTAL2/PB4 pin?
The XTAL2/PB4 pin has a series resistor on 4 of 5 designs, most often 4.7 kΩ (then 47 Ω). Counted from the KiCad layouts of 5 open source designs using the ATtiny85V-10S.
What decoupling capacitors do designs use on the ATtiny85V-10S VCC pin?
The VCC pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 5 open source designs using the ATtiny85V-10S.
Which microcontrollers do boards using the ATtiny85V-10S use?
Most are built on AVR/Arduino (5).
How big is a typical board using the ATtiny85V-10S?
The median is 72.7 × 69.8 mm, and 80% are two-layer designs.
What is the most popular open source board using the ATtiny85V-10S?
By GitHub stars, Sgb mbc5 1-4 by MouseBiteLabs, with 40 stars.
Can I simulate one of these boards using the ATtiny85V-10S before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.