7 open source boards using the BQ25180YBGR
Real designs built with the BQ25180YBGR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
D4 small
unsurv
32 × 45 mm53 parts4LGPL-3.073RP2040/RP2350
Mp3-player
stefanVanadium
38.2 × 99.6 mm113 parts4LMIT0STM32
Datalogger
wngandu
20 × 12 mm65 parts6LNo license0ESP32
PinJammerV01
pinqin
66 × 133.4 mm63 parts2LNo license0ESP32
D4 small pcb panel
unsurv
83 × 109 mm53 parts4LGPL-3.073PGC USB+W Module
HandHeldLegend
50.8 × 32.7 mm40 parts4LNo license15Dial me spinner base
tyevco
57.6 × 46 mm17 parts4LNo license0
How designs wire the BQ25180YBGR
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the BQ25180YBGR connects to, and the resistors, capacitors and other passives placed on it.
- The BAT_C2 pin has a decoupling capacitor on 5 of 5 designs, most often 1 µF (then 4.7 µF).
- The TS/MR_D1 pin has a resistor to GND on 4 of 5 designs, most often 10 kΩ.
- The IN_A2 pin is tied to VBUS on 4 of 5 designs.
- The SYS_B2 pin is tied to VSYS on 4 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| /INT_A1pin A1 | Connected to: The microcontroller 40% · not connected 20% |
|
| IN_A2pin A2 | Connected to: VBUS 80% · a signal 20% | — |
| SCL_B1pin B1 | Connected to: A connector 60%, the microcontroller 60% |
|
| SYS_B2pin B2 | Connected to: VSYS 80% · a signal 20% | — |
| SDA_C1pin C1 | Connected to: A connector 60%, the microcontroller 60% |
|
| BAT_C2pin C2 | Connected to: VBAT 60% · a signal 40% |
|
| TS/MR_D1pin D1 | Connected to: Signal 100% |
|
| GND_D2pin D2 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include D4 small pcb by unsurv, PGC USB+W Module by HandHeldLegend, PinJammerV01 by pinqin and Mp3-player by stefanVanadium.
The BQ25180YBGR in open source designs
The gallery holds 7 open source boards using the BQ25180YBGR from 6 GitHub repositories; a typical one measures about 50.8 × 46 mm and carries around 53 components.
86% use four copper layers or more, and 43% carry an open source license.
The most starred is D4 small pcb by unsurv.
Microcontrollers on boards using the BQ25180YBGR
What boards using the BQ25180YBGR are built for
BQ25180YBGR: common questions
Where can I find a BQ25180YBGR reference design?
Each of the 7 boards on this page is a real design using the BQ25180YBGR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the BQ25180YBGR BAT_C2 pin?
The BAT_C2 pin has a decoupling capacitor on 5 of 5 designs, most often 1 µF (then 4.7 µF). Counted from the KiCad layouts of 6 open source designs using the BQ25180YBGR.
What resistor goes on the BQ25180YBGR TS/MR_D1 pin?
The TS/MR_D1 pin has a resistor to GND on 4 of 5 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the BQ25180YBGR.
How is the BQ25180YBGR IN_A2 pin connected?
The IN_A2 pin is tied to VBUS on 4 of 5 designs. Counted from the KiCad layouts of 6 open source designs using the BQ25180YBGR.
Which microcontrollers do boards using the BQ25180YBGR use?
Most are built on ESP32 (3), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the BQ25180YBGR?
The median is 50.8 × 46 mm, and 14% are two-layer designs.
What is the most popular open source board using the BQ25180YBGR?
By GitHub stars, D4 small pcb by unsurv, with 73 stars.
Can I simulate one of these boards using the BQ25180YBGR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.