7 open source boards using the C130026
Real designs built with the C130026, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Cell sim
atopile
220 × 110 mm1152 parts4LMIT24ESP32
Hex master motor control circuit
csiz
64 × 86 mm236 parts4LMIT92.12
jntaimo
176 × 56 mm76 parts4LNo license0Segway Bot V7
jntaimo
153 × 48 mm68 parts4LNo license0STM32
CrazyCar Prototype -IN DEVELOPMENT-
Matei2010
72 × 103 mm57 parts2LNo license0Cell
atopile
92.9 × 7.9 mm63 parts4LMIT24Hex master cable extender circuit
csiz
160 × 70 mm75 parts2LMIT9
How designs wire the C130026
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the C130026 connects to, and the resistors, capacitors and other passives placed on it.
- The RESET pin has a pull-up to 3.3V on 3 of 5 designs, most often 10 kΩ.
- The VCC pin has a decoupling capacitor on 3 of 4 designs, most often 10 µF (then 100 nF).
- The A0 pin has a resistor to GND on 2 of 5 designs, most often 10 kΩ.
- The A1 pin has a resistor to GND on 2 of 5 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| A0pin 1 | Connected to: Signal 60% · GND 20% · 7.4V 20% |
|
| A1pin 2 | Connected to: Signal 60% · 3.3V 40% |
|
| RESETpin 3 | Connected to: Signal 100% |
|
| SD0pin 4 | Connected to: A connector 40% |
|
| SC0pin 5 | Connected to: A connector 40% · GND 20% |
|
| SD1pin 6 | Connected to: A connector 40% · VREF1 20% |
|
| SC1pin 7 | Connected to: A connector 40% |
|
| SD2pin 8 | Connected to: A connector 40% · 3.3V 20% |
|
| SC2pin 9 | Connected to: A connector 50% |
|
| SD3pin 10 | Connected to: A connector 50% |
|
| SC3pin 11 | Connected to: A connector 50% |
|
| GNDpin 12 | Connected to: GND 75% · a signal 25% | — |
| A2pin 21 | Connected to: Signal 75% · 3.3V 25% |
|
| VCCpin 24 | Connected to: 3.3V 75% · a signal 25% |
|
10 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Cell sim by atopile, Hex master cable extender circuit by csiz, Segway Bot V7 by jntaimo and 2.12-PCB by jntaimo.
The C130026 in open source designs
The gallery holds 7 open source boards using the C130026 from 5 GitHub repositories; a typical one measures about 153 × 70 mm and carries around 75 components.
71% use four copper layers or more, and 57% carry an open source license.
The most starred is Cell sim by atopile.
Parts used alongside the C130026
What boards using the C130026 are built for
C130026: common questions
Where can I find a C130026 reference design?
Each of the 7 boards on this page is a real design using the C130026. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the C130026 RESET pin?
The RESET pin has a pull-up to 3.3V on 3 of 5 designs, most often 10 kΩ. Counted from the KiCad layouts of 5 open source designs using the C130026.
What decoupling capacitors do designs use on the C130026 VCC pin?
The VCC pin has a decoupling capacitor on 3 of 4 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 5 open source designs using the C130026.
What resistor goes on the C130026 A0 pin?
The A0 pin has a resistor to GND on 2 of 5 designs, most often 10 kΩ. Counted from the KiCad layouts of 5 open source designs using the C130026.
Which microcontrollers do boards using the C130026 use?
Most are built on ESP32 (1) and STM32 (1).
How big is a typical board using the C130026?
The median is 153 × 70 mm, and 29% are two-layer designs.
What is the most popular open source board using the C130026?
By GitHub stars, Cell sim by atopile, with 24 stars.
Can I simulate one of these boards using the C130026 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.