8 open source boards using the C2934560
Real designs built with the C2934560, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Nsec badge-2025
nsec
89 × 123.4 mm80 parts2LMIT61ESP32
C3 epaper controller w/touch
martinberlin
70.2 × 71 mm58 parts4LApache-2.032ESP32
Defcon32 badge
thehackbat
60 × 100 mm36 parts2LGPL-3.013ESP32
ReactionButton
RunningJoke
86 × 86 mm67 parts2LNo license0ESP32
Smart coaster
chupachupbum
50 × 40 mm31 parts2LNo license0ESP32
Nsec badge-2025-panel
nsec
197 × 249.7 mm80 parts2LMIT61ESP32
C3-27-epaper touch
martinberlin
65.4 × 71 mm46 parts2LCERN-OHL-W-2.023ESP32
Sharp lcd-128x128
martinberlin
50.3 × 33 mm37 parts2LCERN-OHL-W-2.023
How designs wire the C2934560
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the C2934560 connects to, and the resistors, capacitors and other passives placed on it.
- The EN pin has a pull-up to 3.3V on 6 of 6 designs, most often 10 kΩ.
- The 3V3 pin is tied to 3.3V on 6 of 6 designs.
- The IO8 pin has a pull-up to 3.3V on 5 of 6 designs, most often 10 kΩ (then 3.6 kΩ).
- The IO2 pin has a pull-up to 3.3V on 4 of 6 designs, most often 10 kΩ (then 4.7 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| 3V3pin 1 | Connected to: 3.3V 100% | — |
| ENpin 2 | Connected to: Signal 100% |
|
| IO4pin 3 | Connected to: A connector 50% · not connected 33% |
|
| IO5pin 4 | Connected to: A connector 50% · not connected 17% |
|
| IO8pin 7 | Connected to: A connector 50% |
|
| IO9pin 8 | Connected to: A connector 33% |
|
| GNDpin 9, 19, 20, 21, 22, 23, 24, 25, 26, 27 | Connected to: GND 100% | — |
| IO2pin 16 | Connected to: A connector 50% |
|
10 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Nsec badge-2025 by nsec, C3 epaper controller w/touch by martinberlin, C3-27-epaper touch by martinberlin and Defcon32 badge by thehackbat.
The C2934560 in open source designs
The gallery holds 8 open source boards using the C2934560 from 6 GitHub repositories; a typical one measures about 67.8 × 78.5 mm and carries around 52 components.
88% are two-layer designs, the rest use four layers or more, and 75% carry an open source license.
The most starred is Nsec badge-2025 by nsec.
Parts used alongside the C2934560
Microcontrollers on boards using the C2934560
What boards using the C2934560 are built for
C2934560: common questions
Where can I find a C2934560 reference design?
Each of the 8 boards on this page is a real design using the C2934560. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the C2934560 EN pin?
The EN pin has a pull-up to 3.3V on 6 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the C2934560.
How is the C2934560 3V3 pin connected?
The 3V3 pin is tied to 3.3V on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the C2934560.
What pull-up resistor is used on the C2934560 IO8 pin?
The IO8 pin has a pull-up to 3.3V on 5 of 6 designs, most often 10 kΩ (then 3.6 kΩ). Counted from the KiCad layouts of 6 open source designs using the C2934560.
Which microcontrollers do boards using the C2934560 use?
Most are built on ESP32 (8).
How big is a typical board using the C2934560?
The median is 67.8 × 78.5 mm, and 88% are two-layer designs.
What is the most popular open source board using the C2934560?
By GitHub stars, Nsec badge-2025 by nsec, with 61 stars.
Can I simulate one of these boards using the C2934560 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.