9 open source boards using the CA3140

Real designs built with the CA3140, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

9 boardsClear filters|Most starred

How designs wire the CA3140

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the CA3140 connects to, and the resistors, capacitors and other passives placed on it.

  • The NULL pins is left unconnected on 83% of them.
  • The STRB pin is left unconnected on 5 of 6 designs.
  • The - pin has a series resistor on 4 of 6 designs, most often 10 kΩ (then 1 MΩ).
  • Pin 6 has a series resistor on 4 of 6 designs, most often 1 MΩ (then 2.2 kΩ).
NULLpin 1, 5Connected to: Not connected 83%
-pin 2Connected to: Signal 83% · GND 17%
  • Series resistor on 67% · 10 kΩ (1), 1 MΩ (1), 2.2 kΩ (1)
  • Resistor to GND on 33% · 680 Ω (1), 3 kΩ (1)
+pin 3Connected to: A connector 33%
  • Pull-up to VCC on 33% · 15 kΩ (1)
  • Series resistor on 33% · 10 kΩ (2)
Pin 6Connected to: Signal 83% · GND 17%
  • Series resistor on 67% · 1 MΩ (1), 2.2 kΩ (1), 1 kΩ (1)
V+pin 7Connected to: 5V 67% · a signal 33%
  • Decoupling capacitor on 33% · 1 µF (1), 100 nF (1)
STRBpin 8Connected to: Not connected 83% · a signal 17%

1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Amplifier by MarinosK, MicroKit09 IO by electrickery, Philips-GAM-48-303-daughterboard by alexmrqt and Spectrum Analyzer: IF and Log Amp by dmsmccann.

The CA3140 in open source designs

The gallery holds 9 open source boards using the CA3140 from 6 GitHub repositories; a typical one measures about 97.2 × 82.5 mm and carries around 62 components.

100% are two-layer designs, the rest use four layers or more, and 0% carry an open source license.

The most starred is Amplifier by MarinosK.

Microcontrollers on boards using the CA3140

CA3140: common questions

Where can I find a CA3140 reference design?

Each of the 9 boards on this page is a real design using the CA3140. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the CA3140 NULL pin connected?

The NULL pins is left unconnected on 83% of them. Counted from the KiCad layouts of 6 open source designs using the CA3140.

How is the CA3140 STRB pin connected?

The STRB pin is left unconnected on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the CA3140.

What resistor goes on the CA3140 - pin?

The - pin has a series resistor on 4 of 6 designs, most often 10 kΩ (then 1 MΩ). Counted from the KiCad layouts of 6 open source designs using the CA3140.

Which microcontrollers do boards using the CA3140 use?

Most are built on AVR/Arduino (1).

How big is a typical board using the CA3140?

The median is 97.2 × 82.5 mm, and 100% are two-layer designs.

What is the most popular open source board using the CA3140?

By GitHub stars, Amplifier by MarinosK, with 4 stars.

Can I simulate one of these boards using the CA3140 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part