7 open source boards using the CC1110F32RHHR
Real designs built with the CC1110F32RHHR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Openlst hw
OpenLST
60 × 50 mm86 parts4LNo license37OpenLST
diegosvs
60 × 50 mm86 parts4LNo license2HarvardSatelliteGroundstation
AlexFWulff
60 × 50 mm86 parts4LNo license1OPENLST-Hardware
elfenix7
60 × 50 mm86 parts4LNo license0Open lst hw clone
jonnylin22
60 × 50 mm86 parts4LNo license0Ta comm-401
CMUAbstract
43 × 43 mm55 parts4LNo license5Ta comm
CMUAbstract
45 × 45 mm49 parts4LNo license5
How designs wire the CC1110F32RHHR
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the CC1110F32RHHR connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 6 of 7 designs, most often 100 Ω (then 10 kΩ).
- Pin 2 has a decoupling capacitor on 6 of 7 designs, most often 100 nF.
- Pin 3 has a resistor to GND on 6 of 7 designs, most often 1 kΩ.
- Pin 4 has a pull-up to 3.3V on 6 of 7 designs, most often 1 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| Pin 2 | Connected to: 3.3V 86% |
|
| Pin 3 | Connected to: RFFM6403SB 71% |
|
| Pin 4 | Connected to: RFFM6403SB 71% |
|
| Pin 5 | Connected to: Signal 71% |
|
| Pin 6 | Connected to: Signal 86% |
|
| Pin 7 | Connected to: A connector 29% |
|
| Pin 8 | Connected to: A connector 29% |
|
| Pin 9 | Connected to: A connector 29% |
|
| Pin 10 | Connected to: 3.3V 86% |
|
| Pin 11 | Connected to: Signal 100% |
|
| Pin 12 | Connected to: Signal 100% |
|
| Pin 13 | Connected to: Signal 100% |
|
| Pin 14 | Connected to: Signal 86% |
|
| Pin 17 | Connected to: Signal 86% |
|
| Pin 18 | Connected to: Not connected 86% | — |
| Pin 19 | Connected to: 3.3V 86% |
|
| Pin 20 | Connected to: Not connected 86% | — |
| Pin 21 | Connected to: Signal 100% |
|
| Pin 22 | Connected to: 3.3V 100% |
|
| Pin 23 | Connected to: Signal 100% |
|
| Pin 24 | Connected to: Signal 100% |
|
| Pin 25 | Connected to: 3.3V 100% |
|
| Pin 26 | Connected to: 3.3V 100% |
|
| Pin 27 | Connected to: Signal 100% |
|
| Pin 28 | Connected to: 3.3V 100% |
|
| Pin 29 | Connected to: 3.3V 100% |
|
| Pin 30 | Connected to: Signal 100% |
|
| Pin 31 | Connected to: TLV803SDBZR 83% |
|
| Pin 32 | Connected to: 4259-63 67% |
|
| Pin 33 | Connected to: RFFM6403SB 83% |
|
| Pin 34 | Connected to: Signal 100% |
|
| Pin 35 | Connected to: Signal 100% |
|
| Pin 36 | Connected to: Signal 100% |
|
| Pin 37 | Connected to: GND 100% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Openlst hw by OpenLST, Ta comm by CMUAbstract, OpenLST by diegosvs and HarvardSatelliteGroundstation by AlexFWulff.
The CC1110F32RHHR in open source designs
The gallery holds 7 open source boards using the CC1110F32RHHR from 6 GitHub repositories; a typical one measures about 60 × 50 mm and carries around 86 components.
100% use four copper layers or more, and 0% carry an open source license.
The most starred is Openlst hw by OpenLST.
Parts used alongside the CC1110F32RHHR
What boards using the CC1110F32RHHR are built for
CC1110F32RHHR: common questions
Where can I find a CC1110F32RHHR reference design?
Each of the 7 boards on this page is a real design using the CC1110F32RHHR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the CC1110F32RHHR pin 1?
Pin 1 has a series resistor on 6 of 7 designs, most often 100 Ω (then 10 kΩ). Counted from the KiCad layouts of 7 open source designs using the CC1110F32RHHR.
What decoupling capacitors do designs use on the CC1110F32RHHR pin 2?
Pin 2 has a decoupling capacitor on 6 of 7 designs, most often 100 nF. Counted from the KiCad layouts of 7 open source designs using the CC1110F32RHHR.
What resistor goes on the CC1110F32RHHR pin 3?
Pin 3 has a resistor to GND on 6 of 7 designs, most often 1 kΩ. Counted from the KiCad layouts of 7 open source designs using the CC1110F32RHHR.
What parts are used alongside the CC1110F32RHHR?
The FT5HNBPK27.0-T1, LM1117IMP-3.3/NOPB, LT1086-3.6, RFFM6403SB and TLV803SDBZR appear in the most repositories here.
How big is a typical board using the CC1110F32RHHR?
The median is 60 × 50 mm, and 0% are two-layer designs.
What is the most popular open source board using the CC1110F32RHHR?
By GitHub stars, Openlst hw by OpenLST, with 37 stars.
Can I simulate one of these boards using the CC1110F32RHHR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.