7 open source boards using the CNY17-1
Real designs built with the CNY17-1, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Datalogger-HW
Velli20
100 × 99 mm101 parts4LMIT1CarteDMX512vF767
IOGS-LEnsE-platforms
109.9 × 134.6 mm79 parts2LNo license0CarteDMX512vF767
jvillemejane
109.9 × 134.6 mm79 parts2LNo license0ACDC120V24
Anastien
85 × 128.5 mm71 parts2LNo license0AVR/Arduino
ArduFM2612
rimowals
87.5 × 95 mm51 parts2LNo license0CarteDmx512vFinale
jvillemejane
86.4 × 118.7 mm60 parts2LNo license0AVR/Arduino
CarteExtensionMidi
jvillemejane
59.1 × 74.3 mm11 parts2LNo license0
How designs wire the CNY17-1
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the CNY17-1 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 5 of 5 designs, most often 220 Ω (then 4.7 kΩ).
- Pin 4 is tied to GND on 5 of 5 designs.
- Pin 6 is left unconnected on 5 of 5 designs.
- Pin 5 has a pull-up to 3.3V on 4 of 5 designs, most often 1.2 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| NCpin 3 | Connected to: Not connected 100% | — |
| Pin 4 | Connected to: GND 100% | — |
| Pin 5 | Connected to: The microcontroller 40%, NUCLEO144-H7A3ZI-Q 40% |
|
| Pin 6 | Connected to: Not connected 100% | — |
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Datalogger-HW by Velli20, ACDC120V24 by Anastien, CarteDMX512vF767 by IOGS-LEnsE-platforms and CarteDMX512vF767 by jvillemejane.
The CNY17-1 in open source designs
The gallery holds 7 open source boards using the CNY17-1 from 5 GitHub repositories; a typical one measures about 87.5 × 118.7 mm and carries around 71 components.
86% are two-layer designs, the rest use four layers or more, and 14% carry an open source license.
The most starred is Datalogger-HW by Velli20.
Microcontrollers on boards using the CNY17-1
CNY17-1: common questions
Where can I find a CNY17-1 reference design?
Each of the 7 boards on this page is a real design using the CNY17-1. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the CNY17-1 pin 1?
Pin 1 has a series resistor on 5 of 5 designs, most often 220 Ω (then 4.7 kΩ). Counted from the KiCad layouts of 5 open source designs using the CNY17-1.
How is the CNY17-1 pin 4 connected?
Pin 4 is tied to GND on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the CNY17-1.
How is the CNY17-1 pin 6 connected?
Pin 6 is left unconnected on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the CNY17-1.
What parts are used alongside the CNY17-1?
The 4011, L7805, LM358, MAX485 and MSGEQ7 appear in the most repositories here.
Which microcontrollers do boards using the CNY17-1 use?
Most are built on AVR/Arduino (2) and ESP32 (1).
How big is a typical board using the CNY17-1?
The median is 87.5 × 118.7 mm, and 86% are two-layer designs.
What is the most popular open source board using the CNY17-1?
By GitHub stars, Datalogger-HW by Velli20, with 1 stars.
Can I simulate one of these boards using the CNY17-1 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.