13 open source boards using the DMP1045U-7

Real designs built with the DMP1045U-7, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

13 boardsClear filters|Most starred

How designs wire the DMP1045U-7

Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the DMP1045U-7 connects to, and the resistors, capacitors and other passives placed on it.

  • The G pin has a resistor to GND on 13 of 13 designs, most often 100 kΩ (then 1 kΩ).
  • The S pin is tied to 3.3V on 13 of 13 designs.
  • The D pin is tied to 3.3V on 13 of 13 designs.
Gpin 1Connected to: MMDT2907A-7-F 92%
  • Resistor to GND on 100% · 100 kΩ (12), 1 kΩ (1)
Spin 2Connected to: 3.3V 100%
Dpin 3Connected to: 3.3V 100%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Whofi by jedarden-org, ESP32Marauder NetNinja by bpmcircuits, ESP32Marauder by yyewolf and Marauder-T-display-TTGO by AliHj98.

The DMP1045U-7 in open source designs

The gallery holds 13 open source boards using the DMP1045U-7 from 13 GitHub repositories; a typical one measures about 78.5 × 20.1 mm and carries around 45 components.

92% are two-layer designs, the rest use four layers or more, and 77% carry an open source license.

The most starred is Whofi by jedarden-org.

Microcontrollers on boards using the DMP1045U-7

DMP1045U-7: common questions

Where can I find a DMP1045U-7 reference design?

Each of the 13 boards on this page is a real design using the DMP1045U-7. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the DMP1045U-7 G pin?

The G pin has a resistor to GND on 13 of 13 designs, most often 100 kΩ (then 1 kΩ). Counted from the KiCad layouts of 13 open source designs using the DMP1045U-7.

How is the DMP1045U-7 S pin connected?

The S pin is tied to 3.3V on 13 of 13 designs. Counted from the KiCad layouts of 13 open source designs using the DMP1045U-7.

How is the DMP1045U-7 D pin connected?

The D pin is tied to 3.3V on 13 of 13 designs. Counted from the KiCad layouts of 13 open source designs using the DMP1045U-7.

What parts are used alongside the DMP1045U-7?

The AZ1117H-3.3TRE1, ESP32-WROOM-32E-N4 and MMDT2907A-7-F appear in the most repositories here.

Which microcontrollers do boards using the DMP1045U-7 use?

Most are built on ESP32 (13).

How big is a typical board using the DMP1045U-7?

The median is 78.5 × 20.1 mm, and 92% are two-layer designs.

What is the most popular open source board using the DMP1045U-7?

By GitHub stars, Whofi by jedarden-org, with 98 stars.

Can I simulate one of these boards using the DMP1045U-7 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part