7 open source boards using the DP83848C

Real designs built with the DP83848C, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

7 boardsClear filters|Most starred

How designs wire the DP83848C

Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the DP83848C connects to, and the resistors, capacitors and other passives placed on it.

  • The TD- pin has a pull-up to 3.3V on 6 of 7 designs, most often 49.9 Ω.
  • The TD+ pin has a pull-up to 3.3V on 6 of 7 designs, most often 49.9 Ω.
  • The PFBIN1 pin has a capacitor to GND on 6 of 7 designs, most often 100 nF (then 10 µF).
  • The RESERVED pins have a pull-up to 3.3V on 6 of 7 designs, most often 2.2 kΩ.
TX_CLKpin 1Connected to: Not connected 71% · a signal 29%
TX_ENpin 2Connected to: The microcontroller 29%
  • Series resistor on 57% · 33 Ω (3), 49.9 Ω (1)
TXD_0pin 3Connected to: The microcontroller 29%
  • Series resistor on 57% · 33 Ω (3), 49.9 Ω (1)
TXD_1pin 4Connected to: The microcontroller 29%
  • Series resistor on 57% · 33 Ω (3), 49.9 Ω (1)
Pin 8Connected to: Not connected 100%
Pin 9Connected to: Not connected 100%
Pin 10Connected to: Not connected 100%
Pin 11Connected to: Not connected 100%
Pin 12Connected to: Not connected 100%
RD-pin 13Connected to: A connector 86%
  • Pull-up to 3.3V on 71% · 49.9 Ω (5)
RD+pin 14Connected to: A connector 86%
  • Pull-up to 3.3V on 71% · 49.9 Ω (5)
AGNDpin 15, 19Connected to: GND 86%
TD-pin 16Connected to: A connector 86%
  • Pull-up to 3.3V on 86% · 49.9 Ω (6)
TD+pin 17Connected to: A connector 86%
  • Pull-up to 3.3V on 86% · 49.9 Ω (6)
PFBIN1pin 18Connected to: Signal 86%
  • Capacitor to GND on 86% · 100 nF (17), 10 µF (5), 4.7 µF (1)
RESERVEDpin 20, 21Connected to: Signal 86%
  • Pull-up to 3.3V on 86% · 2.2 kΩ (12)
AVDD33pin 22Connected to: 3.3V 86%
  • Decoupling capacitor on 57% · 100 nF (7), 1 µF (1)
PFBOUTpin 23Connected to: Signal 86%
  • Capacitor to GND on 86% · 100 nF (17), 10 µF (5), 4.7 µF (1)
RBIASpin 24Connected to: Signal 86%
  • Resistor to GND on 71% · 4.87 kΩ (4), 4.87 Ω (1)
25M_OUTpin 25Connected to: Not connected 86%
AN_EN/LED_ACT/COLpin 26Connected to: A connector 29%
  • Pull-up to 3.3V on 43% · 2.2 kΩ (3)
  • Series resistor on 43% · 220 Ω (2), 33 Ω (1)
AN1/LED_SPEEDpin 27Connected to: Signal 57% · not connected 43%
  • Pull-up to 3.3V on 43% · 2.2 kΩ (3)
AN0/LED_LINKpin 28Connected to: A connector 43%
  • Pull-up to 3.3V on 43% · 2.2 kΩ (3)
  • Series resistor on 43% · 220 Ω (2), 33 Ω (1)
RESETpin 29Connected to: The microcontroller 43%
  • Pull-up to 3.3V on 43% · 12 kΩ (1), 1.5 kΩ (1), 2.2 kΩ (1)
MDIOpin 30Connected to: The microcontroller 71%
  • Pull-up to 3.3V on 71% · 2.2 kΩ (4), 1.5 kΩ (1)
IOVDD33pin 32, 48Connected to: 3.3V 86%
  • Decoupling capacitor on 57% · 100 nF (10), 10 µF (1)
X2pin 33Connected to: Not connected 86%
X1pin 34Connected to: The microcontroller 29%
  • Series resistor on 43% · 49.9 Ω (1), 0 Ω (1), 33 Ω (1)
IOGNDpin 35, 47Connected to: GND 86%
DGNDpin 36Connected to: GND 86%
PFBIN2pin 37Connected to: Signal 86%
  • Capacitor to GND on 86% · 100 nF (17), 10 µF (5), 4.7 µF (1)
RX_CLKpin 38Connected to: Not connected 71% · a signal 29%
RX_DV/MII_MODEpin 39Connected to: The microcontroller 29%
  • Pull-up to 3.3V on 57% · 2.2 kΩ (4)
CRS/CRS_DV/LED_CFGpin 40Connected to: The microcontroller 29%
  • Series resistor on 43% · 33 Ω (2), 49.9 Ω (1)
COL/PHY_AD0pin 42Connected to: Not connected 71% · a signal 29%
RXD_0/PHY_AD1pin 43Connected to: The microcontroller 29%
  • Series resistor on 57% · 33 Ω (3), 49.9 Ω (1)
RXD_1/PHY_AD2pin 44Connected to: The microcontroller 29%
  • Series resistor on 57% · 33 Ω (3), 49.9 Ω (1)
RXD_2/PHY_AD3pin 45Connected to: Not connected 71% · a signal 29%
RXD_3/PHY_AD4pin 46Connected to: Not connected 71% · a signal 29%

5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include EsperDNS by zachmorr, LinuxBoard by joeperri95, Db25 bob v2 by coon42 and DP83848C-EvalBoard by kuellenberg.

The DP83848C in open source designs

The gallery holds 7 open source boards using the DP83848C from 7 GitHub repositories; a typical one measures about 100 × 95 mm and carries around 152 components.

50% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.

The most starred is EsperDNS by zachmorr.

Microcontrollers on boards using the DP83848C

What boards using the DP83848C are built for

DP83848C: common questions

Where can I find a DP83848C reference design?

Each of the 7 boards on this page is a real design using the DP83848C. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the DP83848C TD- pin?

The TD- pin has a pull-up to 3.3V on 6 of 7 designs, most often 49.9 Ω. Counted from the KiCad layouts of 7 open source designs using the DP83848C.

What pull-up resistor is used on the DP83848C TD+ pin?

The TD+ pin has a pull-up to 3.3V on 6 of 7 designs, most often 49.9 Ω. Counted from the KiCad layouts of 7 open source designs using the DP83848C.

How is the DP83848C PFBIN1 pin connected?

The PFBIN1 pin has a capacitor to GND on 6 of 7 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 7 open source designs using the DP83848C.

Which microcontrollers do boards using the DP83848C use?

Most are built on STM32 (4), ESP32 (1) and PIC (1).

How big is a typical board using the DP83848C?

The median is 100 × 95 mm, and 50% are two-layer designs.

What is the most popular open source board using the DP83848C?

By GitHub stars, EsperDNS by zachmorr, with 174 stars.

Can I simulate one of these boards using the DP83848C before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part