5 open source boards using the DWM1000

Real designs built with the DWM1000, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

5 boardsClear filters|Most starred

How designs wire the DWM1000

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the DWM1000 connects to, and the resistors, capacitors and other passives placed on it.

  • The EXTON pin is left unconnected on 5 of 5 designs.
  • The GPIO7 pin is left unconnected on 5 of 5 designs.
  • The GPIO6 pin is left unconnected on 5 of 5 designs.
  • The GPIO5 pin is left unconnected on 5 of 5 designs.
EXTONpin 1Connected to: Not connected 100%
WAKEUPpin 2Connected to: Not connected 60% · a signal 40%
GPIO7pin 4Connected to: Not connected 100%
VDDAONpin 5Connected to: 3.3V 80% · a signal 20%
  • Decoupling capacitor on 40% · 4.7 µF (2), 1 µF (1), 100 nF (1)
VDD3V3@1pin 6Connected to: 3.3V 80% · a signal 20%
  • Decoupling capacitor on 40% · 4.7 µF (2), 1 µF (1), 100 nF (1)
VDD3V3@2pin 7Connected to: 3.3V 80% · a signal 20%
  • Decoupling capacitor on 40% · 4.7 µF (2), 1 µF (1), 100 nF (1)
VSS@1pin 8Connected to: GND 100%
GPIO6pin 9Connected to: Not connected 100%
GPIO5pin 10Connected to: Not connected 100%
GPIO4pin 11Connected to: Not connected 100%
GPIO3pin 12Connected to: Not connected 60% · a signal 40%
GPIO2pin 13Connected to: Not connected 60% · a signal 40%
GPIO1pin 14Connected to: Not connected 60% · a signal 40%
GPIO0pin 15Connected to: Not connected 60% · a signal 40%
VSS@2pin 16Connected to: GND 80% · not connected 20%
VSS@3pin 21Connected to: GND 100%
IRQ/GPIO8pin 22Connected to: The microcontroller 60%
  • Resistor to GND on 60% · 10 kΩ (2), 1 kΩ (1)
VSS@4pin 23Connected to: GND 100%
VSS@5pin 24Connected to: GND 100%

5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Dwatum by lab11, Flipper UWB by ElectronicCats, Drone by rmingon and Uwb beacon board by cvra.

The DWM1000 in open source designs

The gallery holds 5 open source boards using the DWM1000 from 5 GitHub repositories; a typical one measures about 42 × 67 mm and carries around 13 components.

100% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.

The most starred is Dwatum by lab11.

Parts used alongside the DWM1000

Microcontrollers on boards using the DWM1000

DWM1000: common questions

Where can I find a DWM1000 reference design?

Each of the 5 boards on this page is a real design using the DWM1000. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the DWM1000 EXTON pin connected?

The EXTON pin is left unconnected on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the DWM1000.

How is the DWM1000 GPIO7 pin connected?

The GPIO7 pin is left unconnected on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the DWM1000.

How is the DWM1000 GPIO6 pin connected?

The GPIO6 pin is left unconnected on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the DWM1000.

Which microcontrollers do boards using the DWM1000 use?

Most are built on ESP32 (2) and STM32 (1).

How big is a typical board using the DWM1000?

The median is 42 × 67 mm, and 100% are two-layer designs.

What is the most popular open source board using the DWM1000?

By GitHub stars, Dwatum by lab11, with 144 stars.

Can I simulate one of these boards using the DWM1000 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part