8 open source boards using the ESP8285

Real designs built with the ESP8285, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

8 boardsClear filters|Most starred

How designs wire the ESP8285

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the ESP8285 connects to, and the resistors, capacitors and other passives placed on it.

  • The VDDA pins have a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF).
  • The VDDPST pins have a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF).
  • The MTDO pin has a resistor to GND on 4 of 5 designs, most often 4.7 kΩ (then 10 kΩ).
  • The VDD_RTC pin is left unconnected on 4 of 5 designs.
VDDApin 1, 30Connected to: 3.3V 89%
  • Decoupling capacitor on 80% · 100 nF (7), 10 µF (4), 10 nF (2)
LNApin 2Connected to: Signal 60% · not connected 40%
  • Inductor on 40% · 15 µH (1)
VDD3P3pin 3, 4Connected to: 3.3V 80% · a signal 20%
  • Decoupling capacitor on 60% · 100 nF (6), 10 µF (4), 1 µF (2)
VDD_RTCpin 5Connected to: Not connected 80% · 3.3V 20%
TOUTpin 6Connected to: Not connected 80% · a signal 20%
CHIP_ENpin 7Connected to: Signal 80% · 3.3V 20%
  • Pull-up to 3.3V on 60% · 10 kΩ (2), 12 kΩ (1)
XPD_DCDCpin 8Connected to: Signal 60% · not connected 40%
  • Series resistor on 40% · 330 Ω (1), 470 Ω (1)
VDDPSTpin 11, 17Connected to: 3.3V 90%
  • Decoupling capacitor on 80% · 100 nF (11), 10 µF (2), 2.2 µF (2)
MTDOpin 13Connected to: SX1280IMLTRT 60% · GND 20%
  • Resistor to GND on 80% · 4.7 kΩ (2), 10 kΩ (1), 12 kΩ (1)
GPIO0pin 15Connected to: Signal 80% · 3.3V 20%
  • Pull-up to 3.3V on 40% · 10 kΩ (1), 12 kΩ (1)
SD_CMDpin 20Connected to: Not connected 80% · GND 20%
SD_CLKpin 21Connected to: Not connected 80% · GND 20%
SD_DATA_0pin 22Connected to: Not connected 80% · a signal 20%
SD_DATA_1pin 23Connected to: Not connected 80% · GND 20%
XTAL_OUTpin 27Connected to: Not connected 50% · a signal 50%
  • Crystal on 50% · 26 MHz (1)
  • Capacitor to GND on 50% · 5.6 pF (1), 10 pF (1)
XTAL_INpin 28Connected to: Signal 75% · not connected 25%
  • Crystal on 75% · 26 MHz (2)
  • Capacitor to GND on 50% · 5.6 pF (1), 10 pF (1)
VDDDpin 29Connected to: 3.3V 100%
  • Decoupling capacitor on 75% · 100 nF (5), 10 µF (2), 10 nF (1)
RES12Kpin 31Connected to: Signal 75% · not connected 25%
  • Resistor to GND on 75% · 12 kΩ (3)
EXT_RSTpin 32Connected to: Not connected 50% · 3.3V 25% · a signal 25%
  • Capacitor to GND on 50% · 100 nF (1), 10 µF (1), 1 µF (1)
GNDpin 33Connected to: GND 100%

10 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Wiflier8285 by cnlohr, Dual radio pcb by AnyLeaf, Elrs receiver pcb by Prateek-elec and ZenFly F71 by LongDo1902.

The ESP8285 in open source designs

The gallery holds 8 open source boards using the ESP8285 from 6 GitHub repositories; a typical one measures about 39.6 × 37.7 mm and carries around 54 components.

88% use four copper layers or more, and 63% carry an open source license.

The most starred is Wiflier8285 by cnlohr.

Parts used alongside the ESP8285

Microcontrollers on boards using the ESP8285

What boards using the ESP8285 are built for

ESP8285: common questions

Where can I find a ESP8285 reference design?

Each of the 8 boards on this page is a real design using the ESP8285. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the ESP8285 VDDA pin?

The VDDA pins have a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the ESP8285.

What decoupling capacitors do designs use on the ESP8285 VDDPST pin?

The VDDPST pins have a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the ESP8285.

What resistor goes on the ESP8285 MTDO pin?

The MTDO pin has a resistor to GND on 4 of 5 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the ESP8285.

Which microcontrollers do boards using the ESP8285 use?

Most are built on ESP8266 (4), RP2040/RP2350 (3) and STM32 (1).

How big is a typical board using the ESP8285?

The median is 39.6 × 37.7 mm, and 13% are two-layer designs.

What is the most popular open source board using the ESP8285?

By GitHub stars, Wiflier8285 by cnlohr, with 92 stars.

Can I simulate one of these boards using the ESP8285 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part