5 open source boards using the HLK-PM03
Real designs built with the HLK-PM03, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP8266
ReflowOven
hjf
58.4 × 101.6 mm45 parts2LMIT4ESP32
LEDDs
VasilKalchev
95 × 46 mm84 parts2LMIT3New dimmer
harshverma27
59 × 67 mm19 parts2LNo license0ESP32
UVTimer
willy40
58.5 × 32.1 mm10 parts2LMIT0ESP8266
FilPilote
LudovicLemarinel
50 × 40 mm14 parts2LNo license3
How designs wire the HLK-PM03
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the HLK-PM03 connects to, and the resistors, capacitors and other passives placed on it.
- The -VOUT_3 pin is tied to GND on 4 of 5 designs.
- The AC/L_1 pin has a series resistor on 2 of 5 designs, most often 10 kΩ (then 470 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| AC/L_1pin 1 | Connected to: A connector 80% |
|
| -VOUT_3pin 3 | Connected to: GND 80% · a signal 20% | — |
| +VOUT_4pin 4 | Connected to: 3.3V 60% · a signal 40% | — |
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ReflowOven by hjf, FilPilote by LudovicLemarinel, LEDDs by VasilKalchev and New dimmer by harshverma27.
The HLK-PM03 in open source designs
The gallery holds 5 open source boards using the HLK-PM03 from 5 GitHub repositories; a typical one measures about 58.5 × 46 mm and carries around 19 components.
100% are two-layer designs, the rest use four layers or more, and 60% carry an open source license.
The most starred is ReflowOven by hjf.
Parts used alongside the HLK-PM03
What boards using the HLK-PM03 are built for
HLK-PM03: common questions
Where can I find a HLK-PM03 reference design?
Each of the 5 boards on this page is a real design using the HLK-PM03. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the HLK-PM03 -VOUT_3 pin connected?
The -VOUT_3 pin is tied to GND on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the HLK-PM03.
What resistor goes on the HLK-PM03 AC/L_1 pin?
The AC/L_1 pin has a series resistor on 2 of 5 designs, most often 10 kΩ (then 470 Ω). Counted from the KiCad layouts of 5 open source designs using the HLK-PM03.
Which microcontrollers do boards using the HLK-PM03 use?
Most are built on ESP32 (2) and ESP8266 (2).
How big is a typical board using the HLK-PM03?
The median is 58.5 × 46 mm, and 100% are two-layer designs.
What is the most popular open source board using the HLK-PM03?
By GitHub stars, ReflowOven by hjf, with 4 stars.
Can I simulate one of these boards using the HLK-PM03 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.