7 open source boards using the INA233
Real designs built with the INA233, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Maxwell main
azonenberg
280 × 195 mm987 parts8LBSD-3-Clause193ESP32
Flight Computer V1
colin-skinner
77.5 × 66 mm92 parts2LNo license0Raspberry Pi
RPi power logger
Wireb
65 × 30 mm40 parts2LMIT0MacValve
AntumArk
66 × 97 mm36 parts2LNo license0AR PDM INA233 breakout
align-racing-uia
21.6 × 13.7 mm3 parts2LNo license5ESP32
(OLD) Flight Computer V1
colin-skinner
57.4 × 68.3 mm92 parts2LNo license0ESP32
Test Rocket Board
colin-skinner
68 × 66 mm79 parts2LNo license0
How designs wire the INA233
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the INA233 connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 3.3V on 4 of 5 designs, most often 4.7 kΩ (then 10 kΩ).
- The SCL pin has a pull-up to 3.3V on 4 of 5 designs, most often 4.7 kΩ (then 10 kΩ).
- The VS pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF (then 470 nF).
- The VBUS pin has a series resistor on 3 of 5 designs, most often 50 mΩ (then 200 mΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| A1pin 1 | Connected to: GND 60% · 3.3V 20% · a signal 20% | — |
| A0pin 2 | Connected to: Signal 60% · GND 40% |
|
| ALERTpin 3 | Connected to: A connector 60% · not connected 20% |
|
| SDApin 4 | Connected to: A connector 60% |
|
| SCLpin 5 | Connected to: A connector 60% |
|
| VSpin 6 | Connected to: 3.3V 80% · a signal 20% |
|
| GNDpin 7 | Connected to: GND 100% | — |
| VBUSpin 8 | Connected to: A connector 60% · VBUS 20% |
|
| VIN-pin 9 | Connected to: A connector 40% |
|
| VIN+pin 10 | Connected to: A connector 40% · 5V 20% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Maxwell main by azonenberg, AR PDM INA233 breakout by align-racing-uia, MacValve by AntumArk and Flight Computer V1 by colin-skinner.
The INA233 in open source designs
The gallery holds 7 open source boards using the INA233 from 5 GitHub repositories; a typical one measures about 66 × 66 mm and carries around 79 components.
86% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.
The most starred is Maxwell main by azonenberg.
Microcontrollers on boards using the INA233
What boards using the INA233 are built for
INA233: common questions
Where can I find a INA233 reference design?
Each of the 7 boards on this page is a real design using the INA233. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the INA233 SDA pin?
The SDA pin has a pull-up to 3.3V on 4 of 5 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the INA233.
What pull-up resistor is used on the INA233 SCL pin?
The SCL pin has a pull-up to 3.3V on 4 of 5 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the INA233.
What decoupling capacitors do designs use on the INA233 VS pin?
The VS pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF (then 470 nF). Counted from the KiCad layouts of 5 open source designs using the INA233.
Which microcontrollers do boards using the INA233 use?
Most are built on ESP32 (3), Raspberry Pi (1) and STM32 (1).
How big is a typical board using the INA233?
The median is 66 × 66 mm, and 86% are two-layer designs.
What is the most popular open source board using the INA233?
By GitHub stars, Maxwell main by azonenberg, with 193 stars.
Can I simulate one of these boards using the INA233 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.