10 open source boards using the ISO1044BD
Real designs built with the ISO1044BD, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
MasterBoard A
Gregification
60 × 100 mm163 parts2LMIT5STM32
Base Board Design
WilliamSanchez
199.8 × 150 mm492 parts4LNo license2RP2040/RP2350
HVDC test board
MECSEM
120 × 120 mm287 parts4LGPL-3.00NXP
CoRE2025MainBoard 1
team-continue
100 × 100 mm56 parts2LNo license0- schematic only · 82 partsESP32
SDLH EV
ManchesterStingerMotorsports
82 partsNo license0 STM32
CpuAddOn
logisim-evolution
60.6 × 100 mm138 parts6LMIT18STM32
TBB
formulaslug
139.7 × 63.5 mm159 parts4LNo license7Mini Orion TEM
Gregification
319.7 × 58.4 mm158 parts2LMIT5STM32
Relay Module
Tuskar-Marine
320 × 80 mm134 parts4LNo license6CANE Junction
Gregification
60 × 60 mm91 parts2LMIT5
How designs wire the ISO1044BD
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the ISO1044BD connects to, and the resistors, capacitors and other passives placed on it.
- The VCC1 pin has a decoupling capacitor on 6 of 7 designs, most often 100 nF.
- The VCC2 pin has a decoupling capacitor on 4 of 7 designs, most often 100 nF (then 4.7 µF).
- The CANL pin has a series resistor on 3 of 7 designs, most often 120 Ω.
- The GND2 pin has a series capacitor on 3 of 7 designs, most often 100 nF (then 470 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VCC1pin 1 | Connected to: 3.3V 100% |
|
| GND1pin 4 | Connected to: GND 100% | — |
| CANLpin 5 | Connected to: A connector 71% |
|
| GND2pin 7 | Connected to: GND 57% · a signal 43% |
|
| VCC2pin 8 | Connected to: 5V 57% · a signal 43% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include CpuAddOn by logisim-evolution, TBB by formulaslug, Relay Module by Tuskar-Marine and CANE Junction by Gregification.
The ISO1044BD in open source designs
The gallery holds 10 open source boards using the ISO1044BD from 8 GitHub repositories; a typical one measures about 120 × 100 mm and carries around 148 components.
56% use four copper layers or more, and 50% carry an open source license.
The most starred is CpuAddOn by logisim-evolution.
Microcontrollers on boards using the ISO1044BD
What boards using the ISO1044BD are built for
ISO1044BD: common questions
Where can I find a ISO1044BD reference design?
Each of the 10 boards on this page is a real design using the ISO1044BD. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the ISO1044BD VCC1 pin?
The VCC1 pin has a decoupling capacitor on 6 of 7 designs, most often 100 nF. Counted from the KiCad layouts of 7 open source designs using the ISO1044BD.
What decoupling capacitors do designs use on the ISO1044BD VCC2 pin?
The VCC2 pin has a decoupling capacitor on 4 of 7 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 7 open source designs using the ISO1044BD.
What resistor goes on the ISO1044BD CANL pin?
The CANL pin has a series resistor on 3 of 7 designs, most often 120 Ω. Counted from the KiCad layouts of 7 open source designs using the ISO1044BD.
Which microcontrollers do boards using the ISO1044BD use?
Most are built on STM32 (4), ESP32 (1), NXP (1) and RP2040/RP2350 (1).
How big is a typical board using the ISO1044BD?
The median is 120 × 100 mm, and 44% are two-layer designs.
What is the most popular open source board using the ISO1044BD?
By GitHub stars, CpuAddOn by logisim-evolution, with 18 stars.
Can I simulate one of these boards using the ISO1044BD before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.