5 open source boards using the ISO1541

Real designs built with the ISO1541, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

5 boardsClear filters|Most starred

How designs wire the ISO1541

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the ISO1541 connects to, and the resistors, capacitors and other passives placed on it.

  • The VCC1 pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF.
  • The SDA1 pin has a pull-up to 3.3V on 4 of 5 designs, most often 4.7 kΩ (then 10 kΩ).
  • The SCL1 pin has a pull-up to 3.3V on 4 of 5 designs, most often 4.7 kΩ (then 10 kΩ).
  • The SCL2 pin has a pull-up to 5V on 4 of 5 designs, most often 4.7 kΩ (then 10 kΩ).
VCC1pin 1Connected to: 3.3V 80% · a signal 20%
  • Decoupling capacitor on 80% · 100 nF (5)
SDA1pin 2Connected to: A connector 60%
  • Pull-up to 3.3V on 80% · 4.7 kΩ (2), 10 kΩ (2), 3.3 kΩ (1)
  • Series resistor on 40% · 0 Ω (1), 10 kΩ (1)
SCL1pin 3Connected to: A connector 60%
  • Pull-up to 3.3V on 80% · 4.7 kΩ (2), 10 kΩ (2), 3.3 kΩ (1)
  • Series resistor on 40% · 0 Ω (1), 10 kΩ (1)
GND1pin 4Connected to: GND 80% · a signal 20%
GND2pin 5Connected to: GND 60% · -6V 40%
  • Capacitor to GND on 40% · 100 nF (2)
SCL2pin 6Connected to: Signal 100%
  • Pull-up to 5V on 80% · 4.7 kΩ (1), 10 kΩ (1), 1.5 kΩ (1)
  • Series resistor on 40% · 220 Ω (1), 0 Ω (1)
SDA2pin 7Connected to: Signal 100%
  • Pull-up to 5V on 80% · 4.7 kΩ (1), 10 kΩ (1), 1.5 kΩ (1)
VCC2pin 8Connected to: 5V 80% · GND 20%
  • Decoupling capacitor on 80% · 100 nF (6)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Axiom Micro Mainboard by anuejn, Garden Irrigation Motherboard by vinthewrench, VFD Clock by drewsum and MiniFeedMaster by SG-O.

The ISO1541 in open source designs

The gallery holds 5 open source boards using the ISO1541 from 5 GitHub repositories; a typical one measures about 94 × 88.4 mm and carries around 125 components.

80% are two-layer designs, the rest use four layers or more, and 40% carry an open source license.

The most starred is Axiom Micro Mainboard by anuejn.

Microcontrollers on boards using the ISO1541

What boards using the ISO1541 are built for

ISO1541: common questions

Where can I find a ISO1541 reference design?

Each of the 5 boards on this page is a real design using the ISO1541. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the ISO1541 VCC1 pin?

The VCC1 pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the ISO1541.

What pull-up resistor is used on the ISO1541 SDA1 pin?

The SDA1 pin has a pull-up to 3.3V on 4 of 5 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the ISO1541.

What pull-up resistor is used on the ISO1541 SCL1 pin?

The SCL1 pin has a pull-up to 3.3V on 4 of 5 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the ISO1541.

Which microcontrollers do boards using the ISO1541 use?

Most are built on AVR/Arduino (1), PIC (1) and STM32 (1).

How big is a typical board using the ISO1541?

The median is 94 × 88.4 mm, and 80% are two-layer designs.

What is the most popular open source board using the ISO1541?

By GitHub stars, Axiom Micro Mainboard by anuejn, with 38 stars.

Can I simulate one of these boards using the ISO1541 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part