12 open source boards using the LDO
Real designs built with the LDO, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
YK761
schlae
35 × 20.3 mm141 parts4LNo license133NXP
Ips20
gzweigle
215.9 × 101.6 mm126 parts2LGPL-3.060STM32
DPedal legacy
rukai
154 × 80 mm22 parts2LMIT4AVR/Arduino
Proximity Sensor Mother Board
eigenpi
33 × 88.9 mm40 parts2LNo license2PAM-Using-555-Timer
ExTc-aShiSh
37 × 22.5 mm21 parts2LMIT2NXP
LPC4370-Oscillocope
BigLockie
85.3 × 40.5 mm117 parts4LNo license1STM32
Magrat v0
WRansohoff
64.1 × 72.4 mm78 parts4LMIT0STM32
CAN
cshieldsce
98.7 × 22.5 mm60 parts2LNo license0ESP8266
Wearable e ink
Just4Stan
50.1 × 32.6 mm41 parts4LNo license0ESP8266
Soldering workshop
Just4Stan
50.1 × 32.6 mm41 parts4LNo license0STM32
STM32G431-Dev-Board
larshasstdas
31.3 × 60.5 mm36 parts2LMIT0Tmy
schlae
37.8 × 16.2 mm37 parts2LNo license133
How designs wire the LDO
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the LDO connects to, and the resistors, capacitors and other passives placed on it.
- The EN pin is tied to 5V on 8 of 11 designs.
- The OUT pin has a capacitor to GND on 4 of 5 designs, most often 100 nF (then 1 µF).
- The NC pin has a capacitor to GND on 2 of 5 designs, most often 10 µF (then 100 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ENpin 3 | Connected to: 5V 73% | — |
| NCpin 4 | Connected to: Not connected 40% · GND 20% · 3.3V 40% |
|
| OUTpin 5 | Connected to: 3.3V 40% · not connected 20% · a signal 40% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Tmy by schlae, Ips20 by gzweigle, DPedal legacy by rukai and Proximity Sensor Mother Board by eigenpi.
The LDO in open source designs
The gallery holds 12 open source boards using the LDO from 11 GitHub repositories; a typical one measures about 50.1 × 36.6 mm and carries around 41 components.
58% are two-layer designs, the rest use four layers or more, and 42% carry an open source license.
The most starred is YK761 by schlae.
Parts used alongside the LDO
Microcontrollers on boards using the LDO
What boards using the LDO are built for
LDO: common questions
Where can I find a LDO reference design?
Each of the 12 boards on this page is a real design using the LDO. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LDO EN pin connected?
The EN pin is tied to 5V on 8 of 11 designs. Counted from the KiCad layouts of 11 open source designs using the LDO.
How is the LDO OUT pin connected?
The OUT pin has a capacitor to GND on 4 of 5 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 11 open source designs using the LDO.
How is the LDO NC pin connected?
The NC pin has a capacitor to GND on 2 of 5 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 11 open source designs using the LDO.
What parts are used alongside the LDO?
The 05A20H24P, 4*4*1_7, CH340C_USB, ESP-12F(ESP8266MOD) and N-MOS appear in the most repositories here.
Which microcontrollers do boards using the LDO use?
Most are built on STM32 (4), ESP8266 (2), NXP (2) and AVR/Arduino (1).
How big is a typical board using the LDO?
The median is 50.1 × 36.6 mm, and 58% are two-layer designs.
What is the most popular open source board using the LDO?
By GitHub stars, YK761 by schlae, with 133 stars.
Can I simulate one of these boards using the LDO before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.