6 open source boards using the ESP-12F(ESP8266MOD)
Real designs built with the ESP-12F(ESP8266MOD), from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP8266
ESP12FPSU
R8bert
80 × 100 mm55 parts2LNo license0ESP8266
Chronopixel
alphaseneca
56 × 106 mm46 parts2LMIT0ESP8266
Soldering workshop
Just4Stan
50.1 × 32.6 mm41 parts4LNo license0ESP8266
Wearable e ink
Just4Stan
50.1 × 32.6 mm41 parts4LNo license0ESP8266
Fragaria extend
Zhang-JK
40 × 75 mm80 parts2LNo license2ESP8266
ESP12FPSU backup 27-11
R8bert
70 × 100 mm52 parts2LNo license0
How designs wire the ESP-12F(ESP8266MOD)
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the ESP-12F(ESP8266MOD) connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 5 of 5 designs, most often 100 nF (then 10 µF).
- The RST pin has a pull-up to 3.3V on 4 of 5 designs, most often 10 kΩ (then 5.1 kΩ).
- The EN pin has a pull-up to 3.3V on 4 of 5 designs, most often 10 kΩ (then 5.1 kΩ).
- The GPIO16 pin is left unconnected on 4 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| RSTpin 1 | Connected to: 4*4*1_7 40%, NPN 40% |
|
| ADCpin 2 | Connected to: Not connected 60% · a signal 40% | — |
| ENpin 3 | Connected to: Signal 100% |
|
| GPIO16pin 4 | Connected to: Not connected 80% · a signal 20% | — |
| VCCpin 8 | Connected to: 3.3V 80% · a signal 20% |
|
| GNDpin 9 | Connected to: GND 100% | — |
| GPIO15pin 10 | Connected to: Signal 100% |
|
| GPIO2pin 11 | Connected to: Signal 80% · not connected 20% |
|
| GPIO0pin 12 | Connected to: 4*4*1_7 40%, NPN 40% · not connected 20% |
|
| CS0pin 17 | Connected to: Not connected 80% · a signal 20% | — |
| MISOpin 18 | Connected to: Not connected 80% · a signal 20% | — |
| GPIO9pin 19 | Connected to: Not connected 80% · a signal 20% | — |
| GPIO10pin 20 | Connected to: Not connected 60% · a signal 40% |
|
| MOSIpin 21 | Connected to: Not connected 80% · a signal 20% | — |
| SCLKpin 22 | Connected to: Not connected 80% · a signal 20% | — |
7 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Fragaria extend by Zhang-JK, Chronopixel pcb by alphaseneca, Soldering workshop by Just4Stan and Wearable e ink by Just4Stan.
The ESP-12F(ESP8266MOD) in open source designs
The gallery holds 6 open source boards using the ESP-12F(ESP8266MOD) from 5 GitHub repositories; a typical one measures about 53.1 × 87.5 mm and carries around 49 components.
67% are two-layer designs, the rest use four layers or more, and 17% carry an open source license.
The most starred is Fragaria extend by Zhang-JK.
Parts used alongside the ESP-12F(ESP8266MOD)
Microcontrollers on boards using the ESP-12F(ESP8266MOD)
What boards using the ESP-12F(ESP8266MOD) are built for
ESP-12F(ESP8266MOD): common questions
Where can I find a ESP-12F(ESP8266MOD) reference design?
Each of the 6 boards on this page is a real design using the ESP-12F(ESP8266MOD). Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the ESP-12F(ESP8266MOD) VCC pin?
The VCC pin has a decoupling capacitor on 5 of 5 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the ESP-12F(ESP8266MOD).
What pull-up resistor is used on the ESP-12F(ESP8266MOD) RST pin?
The RST pin has a pull-up to 3.3V on 4 of 5 designs, most often 10 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 5 open source designs using the ESP-12F(ESP8266MOD).
What pull-up resistor is used on the ESP-12F(ESP8266MOD) EN pin?
The EN pin has a pull-up to 3.3V on 4 of 5 designs, most often 10 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 5 open source designs using the ESP-12F(ESP8266MOD).
What parts are used alongside the ESP-12F(ESP8266MOD)?
The 05A20H24P, 4*4*1_7, CH340C_USB, LDO and N-MOS appear in the most repositories here.
Which microcontrollers do boards using the ESP-12F(ESP8266MOD) use?
Most are built on ESP8266 (6).
How big is a typical board using the ESP-12F(ESP8266MOD)?
The median is 53.1 × 87.5 mm, and 67% are two-layer designs.
What is the most popular open source board using the ESP-12F(ESP8266MOD)?
By GitHub stars, Fragaria extend by Zhang-JK, with 2 stars.
Can I simulate one of these boards using the ESP-12F(ESP8266MOD) before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.