8 open source boards using the LM2576T-5
Real designs built with the LM2576T-5, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Mackerel-30
crmaykish
215 × 150 mm127 parts4LMIT96AVR/Arduino
Inefficient coil gun
jamesbrayy
440 × 196 mm151 parts2LMIT1ESP32
RaffstoreControlSystem
Rhynaz
208.3 × 119.4 mm176 parts2LGPL-3.00Raspberry Pi
PicoPLC
antek-elektronik
96 × 98 mm91 parts2LNo license0Caravel breakout QFN
nic0villegasc
150.5 × 110.5 mm60 parts2LNo license0Mackerel-10 v1
crmaykish
210 × 170 mm110 parts4LMIT96AVR/Arduino
V2 board ecar
Jonny999999
160 × 100 mm95 parts2LNo license0Mackerel-08 SBC v1
crmaykish
180 × 120 mm81 parts4LMIT96
How designs wire the LM2576T-5
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the LM2576T-5 connects to, and the resistors, capacitors and other passives placed on it.
- The OUT pin has a inductor on 4 of 6 designs, most often 100 µH (then 47 µH).
- The FB pin is tied to 5V on 4 of 6 designs (a signal on 2).
- The ON/OFF pin is tied to GND on 4 of 6 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VINpin 1 | Connected to: 24V 67% · a signal 33% | — |
| OUTpin 2 | Connected to: Signal 100% |
|
| GNDpin 3 | Connected to: GND 67% · a signal 33% | — |
| FBpin 4 | Connected to: 5V 67% · a signal 33% | — |
| ON/OFFpin 5 | Connected to: GND 67% · a signal 33% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Mackerel-08 SBC v1 by crmaykish, Inefficient coil gun by jamesbrayy, PicoPLC by antek-elektronik and V2 board ecar by Jonny999999.
The LM2576T-5 in open source designs
The gallery holds 8 open source boards using the LM2576T-5 from 6 GitHub repositories; a typical one measures about 194.1 × 119.7 mm and carries around 103 components.
63% are two-layer designs, the rest use four layers or more, and 63% carry an open source license.
The most starred is Mackerel-30 by crmaykish.
Microcontrollers on boards using the LM2576T-5
What boards using the LM2576T-5 are built for
LM2576T-5: common questions
Where can I find a LM2576T-5 reference design?
Each of the 8 boards on this page is a real design using the LM2576T-5. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LM2576T-5 OUT pin connected?
The OUT pin has a inductor on 4 of 6 designs, most often 100 µH (then 47 µH). Counted from the KiCad layouts of 6 open source designs using the LM2576T-5.
How is the LM2576T-5 FB pin connected?
The FB pin is tied to 5V on 4 of 6 designs (a signal on 2). Counted from the KiCad layouts of 6 open source designs using the LM2576T-5.
How is the LM2576T-5 ON/OFF pin connected?
The ON/OFF pin is tied to GND on 4 of 6 designs (a signal on 2). Counted from the KiCad layouts of 6 open source designs using the LM2576T-5.
Which microcontrollers do boards using the LM2576T-5 use?
Most are built on AVR/Arduino (2), ESP32 (1) and Raspberry Pi (1).
How big is a typical board using the LM2576T-5?
The median is 194.1 × 119.7 mm, and 63% are two-layer designs.
What is the most popular open source board using the LM2576T-5?
By GitHub stars, Mackerel-30 by crmaykish, with 96 stars.
Can I simulate one of these boards using the LM2576T-5 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.