10 open source boards using the LM337_SOT223
Real designs built with the LM337_SOT223, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Rear
JQIamo
145 × 157 mm99 parts4LNo license2RP2040/RP2350
Harp.device.quac
AllenNeuralDynamics
90 × 100 mm276 parts4LMIT0PLC RestoMod Digital I/O
akbar-q
68.7 × 164.9 mm132 parts2LNo license0Dac board
robmacl
280 × 100 mm188 parts4LNo license0ESP32
MPPT-Controller
akbar-q
99 × 99 mm96 parts4LNo license0ESP32
020 NiMH Battery Charger
akbar-q
100 × 72.8 mm82 parts2LNo license0Power Supply
jonaheinke
76.5 × 99 mm51 parts2LMIT0DD Supply Test 1
Acmex2564
207 × 92.7 mm84 parts2LNo license19Linear Power Supply for Amplifier
akbar-q
28.6 × 91.2 mm60 parts4LNo license0High Voltage Arc Detector
akbar-q
118.2 × 53.2 mm53 parts4LNo license0
How designs wire the LM337_SOT223
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the LM337_SOT223 connects to, and the resistors, capacitors and other passives placed on it.
- The ADJ pin has a resistor to GND on 5 of 6 designs, most often 2 kΩ (then 120 Ω).
- The VO pin has a decoupling capacitor on 5 of 6 designs, most often 1 µF (then 10 µF).
- The VI pin has a capacitor to GND on 4 of 6 designs, most often 1 µF (then 10 µF).
- The ADJ pin has a pull-up to -2.5V on 3 of 6 designs, most often 120 Ω (then 124 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ADJpin 1 | Connected to: Signal 83% · GND 17% |
|
| VIpin 2 | Connected to: -5V 50% · a signal 50% |
|
| VOpin 3 | Connected to: -2.5V 67% · a signal 33% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include DD Supply Test 1 by Acmex2564, Rear by JQIamo, 020 NiMH Battery Charger by akbar-q and Harp.device.quac by AllenNeuralDynamics.
The LM337_SOT223 in open source designs
The gallery holds 10 open source boards using the LM337_SOT223 from 6 GitHub repositories; a typical one measures about 99.5 × 99 mm and carries around 90 components.
60% use four copper layers or more, and 20% carry an open source license.
The most starred is DD Supply Test 1 by Acmex2564.
Parts used alongside the LM337_SOT223
Microcontrollers on boards using the LM337_SOT223
What boards using the LM337_SOT223 are built for
LM337_SOT223: common questions
Where can I find a LM337_SOT223 reference design?
Each of the 10 boards on this page is a real design using the LM337_SOT223. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LM337_SOT223 ADJ pin?
The ADJ pin has a resistor to GND on 5 of 6 designs, most often 2 kΩ (then 120 Ω). Counted from the KiCad layouts of 6 open source designs using the LM337_SOT223.
What decoupling capacitors do designs use on the LM337_SOT223 VO pin?
The VO pin has a decoupling capacitor on 5 of 6 designs, most often 1 µF (then 10 µF). Counted from the KiCad layouts of 6 open source designs using the LM337_SOT223.
How is the LM337_SOT223 VI pin connected?
The VI pin has a capacitor to GND on 4 of 6 designs, most often 1 µF (then 10 µF). Counted from the KiCad layouts of 6 open source designs using the LM337_SOT223.
Which microcontrollers do boards using the LM337_SOT223 use?
Most are built on ESP32 (2) and RP2040/RP2350 (1).
How big is a typical board using the LM337_SOT223?
The median is 99.5 × 99 mm, and 40% are two-layer designs.
What is the most popular open source board using the LM337_SOT223?
By GitHub stars, DD Supply Test 1 by Acmex2564, with 19 stars.
Can I simulate one of these boards using the LM337_SOT223 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.