31 open source boards using the LM317_SOT-223
Real designs built with the LM317_SOT-223, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
LM317SupplyModule
yingchaotw
47.7 × 37.7 mm30 parts2LCC-BY-SA-4.02Twangilizer
shannon-greenlight
101.3 × 110 mm454 parts4LNo license1ESP32
Clean room slave
trieuhuyduc
165 × 110 mm207 parts2LNo license1RISC-V
PickOMatic-V2
rmingon
100 × 100 mm146 parts4LCERN-OHL-S-2.01STM32
PUTM EV SMART FUSES 2022
PUT-Motorsport
166.4 × 60 mm169 parts4LNo license0E foc
embedded-pro
89.4 × 66.9 mm154 parts2LNo license0STM32
CDFR2025-Carte-OmniAsservissement
robotronik
90 × 90 mm144 parts4LNo license0PLC RestoMod Digital I/O
akbar-q
68.7 × 164.9 mm132 parts2LNo license0Fly High throughput - optogenetics
open-neuroscience
170 × 170 mm94 parts2LGPL-3.00AVR/Arduino
Line follower
rmingon
93.5 × 97.5 mm84 parts2LNo license0ESP32
Reflectometer
FynnK
100 × 100 mm70 parts4LNo license0ThermalDesign
TIH-engineering
100 × 65 mm52 parts2LCC-BY-NC-4.00ESP32
SwiftRocketComputer
radio-satellites
44.5 × 76.5 mm49 parts4LNo license0HBD1E
icosalogic
73.1 × 50 mm48 parts2LMIT0STM32
STM32
TeganJohnson
177.8 × 101.6 mm44 parts2LNo license0AVR/Arduino
Vault-Security-System
bill-chamal
104 × 54 mm23 parts2LMIT0Sensorboard
Cluradev
73 × 50 mm22 parts2LNo license118Pipes main
shannon-greenlight
70.8 × 110 mm207 parts4LNo license2STM32
Jantteri motor pwr
OJ2016
137.7 × 45 mm72 parts2LNo license1ESP32
MPPT-Controller
akbar-q
99 × 99 mm96 parts4LNo license0STM32
STM32newpowerbackup
TeganJohnson
177.8 × 101.6 mm44 parts2LNo license0PIC
PT2399 basd Digital Effect Pedal (Time Manipulator)
codeandrelax
75 × 78 mm113 parts4LMIT1ESP32
020 NiMH Battery Charger
akbar-q
100 × 72.8 mm82 parts2LNo license0Power Supply
jonaheinke
76.5 × 99 mm51 parts2LMIT0Infrared n motors
open-neuroscience
88 × 78 mm25 parts2LGPL-3.00Practise PCB For Clock/Counter
akbar-q
97 × 91 mm67 parts2LNo license0Motors only
open-neuroscience
34.3 × 19.5 mm10 parts2LGPL-3.00Linear Power Supply for Amplifier
akbar-q
28.6 × 91.2 mm60 parts4LNo license0High Voltage Arc Detector
akbar-q
118.2 × 53.2 mm53 parts4LNo license0AVR/Arduino
Draft PCB for Potential Partnership for E-Bike Conversion
akbar-q
162.6 × 86.4 mm44 parts2LNo license0Sub 2 GHz Amplifier
akbar-q
28.6 × 49.5 mm31 parts4LNo license0
How designs wire the LM317_SOT-223
Read from the KiCad layouts of 21 open source designs, one per repository: what each pin of the LM317_SOT-223 connects to, and the resistors, capacitors and other passives placed on it.
- The VI pin has a decoupling capacitor on 15 of 21 designs, most often 100 nF (then 100 µF).
- The ADJ pin has a resistor to GND on 13 of 21 designs, most often 1 kΩ (then 4.3 kΩ).
- The ADJ pin has a pull-up to 9V on 11 of 21 designs, most often 620 Ω (then 220 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ADJpin 1 | Connected to: Signal 81% · GND 19% |
|
| VOpin 2 | Connected to: 3.3V 76% · a signal 24% | — |
| VIpin 3 | Connected to: 12V 76% · a signal 24% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Sensorboard by Cluradev, Pipes main by shannon-greenlight, LM317SupplyModule by yingchaotw and PT2399 basd Digital Effect Pedal (Time Manipulator) by codeandrelax.
The LM317_SOT-223 in open source designs
The gallery holds 31 open source boards using the LM317_SOT-223 from 21 GitHub repositories; a typical one measures about 97 × 86.4 mm and carries around 67 components.
61% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.
The most starred is Sensorboard by Cluradev.
Parts used alongside the LM317_SOT-223
Microcontrollers on boards using the LM317_SOT-223
What boards using the LM317_SOT-223 are built for
LM317_SOT-223: common questions
Where can I find a LM317_SOT-223 reference design?
Each of the 31 boards on this page is a real design using the LM317_SOT-223. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the LM317_SOT-223 VI pin?
The VI pin has a decoupling capacitor on 15 of 21 designs, most often 100 nF (then 100 µF). Counted from the KiCad layouts of 21 open source designs using the LM317_SOT-223.
What resistor goes on the LM317_SOT-223 ADJ pin?
The ADJ pin has a resistor to GND on 13 of 21 designs, most often 1 kΩ (then 4.3 kΩ). Counted from the KiCad layouts of 21 open source designs using the LM317_SOT-223.
What parts are used alongside the LM317_SOT-223?
The AMS1117-3.3, AMS1117-5.0, CD4017, CD4046 and LM2596S-ADJ appear in the most repositories here.
Which microcontrollers do boards using the LM317_SOT-223 use?
Most are built on ESP32 (5), STM32 (5), AVR/Arduino (3) and PIC (1).
How big is a typical board using the LM317_SOT-223?
The median is 97 × 86.4 mm, and 61% are two-layer designs.
What is the most popular open source board using the LM317_SOT-223?
By GitHub stars, Sensorboard by Cluradev, with 118 stars.
Can I simulate one of these boards using the LM317_SOT-223 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.