7 open source boards using the LM4871

Real designs built with the LM4871, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

7 boardsClear filters|Most starred

How designs wire the LM4871

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the LM4871 connects to, and the resistors, capacitors and other passives placed on it.

  • The BYP pin has a capacitor to GND on 6 of 6 designs, most often 1 µF (then 100 nF).
  • The VO1 pin has a series resistor on 5 of 6 designs, most often 20 kΩ (then 68 kΩ).
  • The V+ pin has a decoupling capacitor on 5 of 6 designs, most often 100 nF (then 1 µF).
  • The SDB pin has a pull-up to 5V on 4 of 6 designs, most often 10 kΩ (then 4.7 kΩ).
SDBpin 1Connected to: Signal 83% · GND 17%
  • Pull-up to 5V on 67% · 10 kΩ (3), 4.7 kΩ (1)
  • Series resistor on 33% · 10 kΩ (1), 100 Ω (1)
BYPpin 2Connected to: Signal 100%
  • Capacitor to GND on 100% · 1 µF (5), 100 nF (1)
+pin 3Connected to: Signal 100%
  • Capacitor to GND on 67% · 1 µF (4)
  • Series resistor on 33% · 20 kΩ (3), 10 kΩ (1)
-pin 4Connected to: Signal 100%
  • Series resistor on 67% · 22 kΩ (4), 20 kΩ (3), 68 kΩ (2)
VO1pin 5Connected to: A connector 67%
  • Series resistor on 83% · 20 kΩ (3), 68 kΩ (2)
  • Series capacitor on 33% · 4.7 µF (1)
V+pin 6Connected to: 5V 83% · a signal 17%
  • Decoupling capacitor on 83% · 100 nF (3), 1 µF (2), 22 µF (1)
GNDpin 7Connected to: GND 100%
VO2pin 8Connected to: A connector 67% · not connected 17%
  • Series capacitor on 33% · 4.7 µF (1), 100 nF (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PoEPi hardware by julien8, PCB-MBUS-AquesTalk pico-LSI by botanicfields, RhapsodiePi by theBrutzler and BF-035 by botanicfields.

The LM4871 in open source designs

The gallery holds 7 open source boards using the LM4871 from 6 GitHub repositories; a typical one measures about 85.2 × 53 mm and carries around 81 components.

71% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.

The most starred is PoEPi hardware by julien8.

Parts used alongside the LM4871

Microcontrollers on boards using the LM4871

LM4871: common questions

Where can I find a LM4871 reference design?

Each of the 7 boards on this page is a real design using the LM4871. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the LM4871 BYP pin connected?

The BYP pin has a capacitor to GND on 6 of 6 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 6 open source designs using the LM4871.

What resistor goes on the LM4871 VO1 pin?

The VO1 pin has a series resistor on 5 of 6 designs, most often 20 kΩ (then 68 kΩ). Counted from the KiCad layouts of 6 open source designs using the LM4871.

What decoupling capacitors do designs use on the LM4871 V+ pin?

The V+ pin has a decoupling capacitor on 5 of 6 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 6 open source designs using the LM4871.

Which microcontrollers do boards using the LM4871 use?

Most are built on AVR/Arduino (1), Raspberry Pi (1) and STM32 (1).

How big is a typical board using the LM4871?

The median is 85.2 × 53 mm, and 71% are two-layer designs.

What is the most popular open source board using the LM4871?

By GitHub stars, PoEPi hardware by julien8, with 46 stars.

Can I simulate one of these boards using the LM4871 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part