8 open source boards using the LMP7721MA/NOPB
Real designs built with the LMP7721MA/NOPB, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
PH Orp Board
Loic74650
47 × 62.1 mm44 parts2LMIT20ELARA antenna amplifier
MatejGomboc
200 × 100 mm110 parts4LCERN-OHL-W-2.05UNS Potentiostat
danilocoletto
82 × 100 mm113 parts2LCC0-1.00ESP32
Terasaki V.1
Kiya86
140.5 × 58.6 mm76 parts4LNo license0AVR/Arduino
Mie1001 daq board
Chaospossum
68.6 × 53.3 mm38 parts2LNo license0AVR/Arduino
Mie1001 daq simple
Chaospossum
68.6 × 53.3 mm31 parts2LNo license0ESP32
FMN potentiostat
Kiya86
30 × 60 mm50 parts4LNo license0ESP32
Logic Board
Kiya86
45.3 × 45.3 mm43 parts4LNo license0
How designs wire the LMP7721MA/NOPB
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the LMP7721MA/NOPB connects to, and the resistors, capacitors and other passives placed on it.
- The OUT pin has a series resistor on 4 of 5 designs, most often 350 kΩ (then 10 kΩ).
- The OUT pin has a series capacitor on 4 of 5 designs, most often 100 nF (then 15 nF).
- The V- pin is tied to GND on 4 of 5 designs.
- The N/C_5 pin is left unconnected on 4 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| N/C_2pin 2 | Connected to: Not connected 40% · VREF 20% · a signal 40% |
|
| V-pin 3 | Connected to: GND 80% · a signal 20% | — |
| OUTpin 4 | Connected to: Signal 100% |
|
| N/C_5pin 5 | Connected to: Not connected 80% · VREF 20% | — |
| V+pin 6 | Connected to: 5V 80% · a signal 20% |
|
| N/C_7pin 7 | Connected to: Not connected 40% · VREF 20% · a signal 40% |
|
| IN-pin 8 | Connected to: Signal 100% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PH Orp Board by Loic74650, ELARA antenna amplifier by MatejGomboc, Mie1001 daq board by Chaospossum and UNS Potentiostat by danilocoletto.
The LMP7721MA/NOPB in open source designs
The gallery holds 8 open source boards using the LMP7721MA/NOPB from 5 GitHub repositories; a typical one measures about 68.6 × 59.3 mm and carries around 47 components.
50% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is PH Orp Board by Loic74650.
Parts used alongside the LMP7721MA/NOPB
Microcontrollers on boards using the LMP7721MA/NOPB
What boards using the LMP7721MA/NOPB are built for
LMP7721MA/NOPB: common questions
Where can I find a LMP7721MA/NOPB reference design?
Each of the 8 boards on this page is a real design using the LMP7721MA/NOPB. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LMP7721MA/NOPB OUT pin?
The OUT pin has a series resistor on 4 of 5 designs, most often 350 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the LMP7721MA/NOPB.
How is the LMP7721MA/NOPB V- pin connected?
The V- pin is tied to GND on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the LMP7721MA/NOPB.
How is the LMP7721MA/NOPB N/C_5 pin connected?
The N/C_5 pin is left unconnected on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the LMP7721MA/NOPB.
Which microcontrollers do boards using the LMP7721MA/NOPB use?
Most are built on ESP32 (3) and AVR/Arduino (2).
How big is a typical board using the LMP7721MA/NOPB?
The median is 68.6 × 59.3 mm, and 50% are two-layer designs.
What is the most popular open source board using the LMP7721MA/NOPB?
By GitHub stars, PH Orp Board by Loic74650, with 20 stars.
Can I simulate one of these boards using the LMP7721MA/NOPB before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.