9 open source boards using the LSM303AGR
Real designs built with the LSM303AGR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Womo
muccc
254.9 × 150.1 mm532 parts4LGPL-3.084STM32
CanardBoard
waterloo-rocketry
100 × 70 mm244 parts6LGPL-3.015STM32
CPU Board
jsjolund
100 × 70 mm112 parts2LNo license3ESP32
Stm32h7
nickzentmayer
59.7 × 58.9 mm93 parts6LNo license1DDRN Hardware
davidfobar
33.3 × 54.5 mm51 parts2LNo license1Iot tag cad design
ocean-monitoring-gateway
20.7 × 37.5 mm92 partsNo license0ESP8266
CelestialSync
davidfobar
107 × 52 mm70 parts2LNo license0AVR/Arduino
Selfaware wearable device
aqesters
42 × 15 mm43 parts2LMIT0ESP32
Esp32s3
nickzentmayer
59.7 × 58.9 mm83 parts4LNo license1
How designs wire the LSM303AGR
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the LSM303AGR connects to, and the resistors, capacitors and other passives placed on it.
- The SCL/SPC pin has a pull-up to 3.3V on 7 of 7 designs, most often 10 kΩ (then 1 kΩ).
- The SDA/SDI/SDO pin has a pull-up to 3.3V on 7 of 7 designs, most often 10 kΩ (then 1 kΩ).
- The C1 pin has a capacitor to GND on 7 of 7 designs, most often 220 nF.
- The CS_XL pin has a capacitor to GND on 4 of 7 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SCL/SPCpin 1 | Connected to: The microcontroller 71%, BMP390L 29% |
|
| CS_XLpin 2 | Connected to: Signal 57% · 3.3V 43% |
|
| CS_MAGpin 3 | Connected to: Signal 57% · 3.3V 43% |
|
| SDA/SDI/SDOpin 4 | Connected to: The microcontroller 71%, BMP390L 29% |
|
| C1pin 5 | Connected to: Signal 100% |
|
| GNDpin 6, 8 | Connected to: GND 100% | — |
| VDDpin 9 | Connected to: 3.3V 86% |
|
| VDD_IOpin 10 | Connected to: 3.3V 86% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Womo by muccc, CanardBoard by waterloo-rocketry, CPU Board by jsjolund and DDRN Hardware by davidfobar.
The LSM303AGR in open source designs
The gallery holds 9 open source boards using the LSM303AGR from 8 GitHub repositories; a typical one measures about 59.7 × 58.9 mm and carries around 92 components.
50% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.
The most starred is Womo by muccc.
Parts used alongside the LSM303AGR
Microcontrollers on boards using the LSM303AGR
What boards using the LSM303AGR are built for
LSM303AGR: common questions
Where can I find a LSM303AGR reference design?
Each of the 9 boards on this page is a real design using the LSM303AGR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the LSM303AGR SCL/SPC pin?
The SCL/SPC pin has a pull-up to 3.3V on 7 of 7 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 8 open source designs using the LSM303AGR.
What pull-up resistor is used on the LSM303AGR SDA/SDI/SDO pin?
The SDA/SDI/SDO pin has a pull-up to 3.3V on 7 of 7 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 8 open source designs using the LSM303AGR.
How is the LSM303AGR C1 pin connected?
The C1 pin has a capacitor to GND on 7 of 7 designs, most often 220 nF. Counted from the KiCad layouts of 8 open source designs using the LSM303AGR.
What parts are used alongside the LSM303AGR?
The AP2112K-3.3, USBLC6-2SC6, BMP390L and W25Q32JVSS appear in the most repositories here.
Which microcontrollers do boards using the LSM303AGR use?
Most are built on ESP32 (3), STM32 (2), AVR/Arduino (1) and ESP8266 (1).
How big is a typical board using the LSM303AGR?
The median is 59.7 × 58.9 mm, and 50% are two-layer designs.
What is the most popular open source board using the LSM303AGR?
By GitHub stars, Womo by muccc, with 84 stars.
Can I simulate one of these boards using the LSM303AGR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.