13 open source boards using the BMP390L
Real designs built with the BMP390L, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
NoNameComputer-2.0
PlanAndBuild
40 × 100 mm107 parts4LNo license2AVR/Arduino
Heli avionics
1-max-1
65.5 × 39 mm56 parts4LNo license1STM32
STM32 FlightController
JLjoestar23
42 × 44.4 mm52 parts4LNo license1DDRN Hardware
davidfobar
33.3 × 54.5 mm51 parts2LNo license1STM32
QUADCOPTER
Riskerx
55.9 × 55.9 mm99 parts4LNo license0STM32
UYDUTEPE
emirhanuluakan
85 × 56 mm93 parts6LCERN-OHL-W-2.00Microchip SAM
Vanguard new
SpacePicklesRocketry
50.3 × 40 mm85 parts4LNo license0ESP32
Bedroom-Engineering-Propulsive-Landing-Project
nimishcoder1232
45 × 81 mm70 parts4LNo license0ESP8266
CelestialSync
davidfobar
107 × 52 mm70 parts2LNo license0Nordic nRF
Altimeter
klownfish
12 × 34 mm36 parts4LNo license0Altimeter2
klownfish
14 × 30 mm13 parts4LNo license002 04 barometer BMP390L I2C
nyuad-space
22 × 22 mm11 parts2LNo license1STM32
Middle
StanZalewski
87.9 × 37.5 mm25 parts2LNo license0
How designs wire the BMP390L
Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the BMP390L connects to, and the resistors, capacitors and other passives placed on it.
- The VDDIO pin has a decoupling capacitor on 10 of 12 designs, most often 100 nF (then 22 µF).
- The VDD pin has a decoupling capacitor on 10 of 12 designs, most often 100 nF (then 22 µF).
- The SCK/SCL pin has a pull-up to 3.3V on 8 of 12 designs, most often 4.7 kΩ (then 2.2 kΩ).
- The SDI/SDO/SDA pin has a pull-up to 3.3V on 8 of 12 designs, most often 4.7 kΩ (then 2.2 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDIOpin 1 | Connected to: 3.3V 100% |
|
| SCK/SCLpin 2 | Connected to: The microcontroller 67%, a connector 25% |
|
| VSS/GNDpin 3, 8, 9 | Connected to: GND 100% | — |
| SDI/SDO/SDApin 4 | Connected to: The microcontroller 67%, a connector 25% |
|
| CSpin 6 | Connected to: The microcontroller 25% · 3.3V 42% |
|
| VDDpin 10 | Connected to: 3.3V 100% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include NoNameComputer-2.0 by PlanAndBuild, Heli avionics by 1-max-1, DDRN Hardware by davidfobar and STM32 FlightController by JLjoestar23.
The BMP390L in open source designs
The gallery holds 13 open source boards using the BMP390L from 12 GitHub repositories; a typical one measures about 45 × 44.4 mm and carries around 56 components.
69% use four copper layers or more, and 8% carry an open source license.
The most starred is NoNameComputer-2.0 by PlanAndBuild.
Parts used alongside the BMP390L
Microcontrollers on boards using the BMP390L
What boards using the BMP390L are built for
BMP390L: common questions
Where can I find a BMP390L reference design?
Each of the 13 boards on this page is a real design using the BMP390L. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the BMP390L VDDIO pin?
The VDDIO pin has a decoupling capacitor on 10 of 12 designs, most often 100 nF (then 22 µF). Counted from the KiCad layouts of 12 open source designs using the BMP390L.
What decoupling capacitors do designs use on the BMP390L VDD pin?
The VDD pin has a decoupling capacitor on 10 of 12 designs, most often 100 nF (then 22 µF). Counted from the KiCad layouts of 12 open source designs using the BMP390L.
What pull-up resistor is used on the BMP390L SCK/SCL pin?
The SCK/SCL pin has a pull-up to 3.3V on 8 of 12 designs, most often 4.7 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 12 open source designs using the BMP390L.
What parts are used alongside the BMP390L?
The AP2112K-3.3, BMI270, LSM303AGR and W25Q32JVSS appear in the most repositories here.
Which microcontrollers do boards using the BMP390L use?
Most are built on STM32 (5), AVR/Arduino (1), ESP32 (1) and ESP8266 (1).
How big is a typical board using the BMP390L?
The median is 45 × 44.4 mm, and 31% are two-layer designs.
What is the most popular open source board using the BMP390L?
By GitHub stars, NoNameComputer-2.0 by PlanAndBuild, with 2 stars.
Can I simulate one of these boards using the BMP390L before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.