10 open source boards using the MCP23008T-E/SS
Real designs built with the MCP23008T-E/SS, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
PiADC2
capconix
65 × 56 mm70 parts2LNo license1STM32
UMDv3
db-electronics
147.3 × 83.8 mm67 parts2LCERN-OHL-1.21STM32
EPS
MatthiasGeorgImhof
80 × 80 mm238 parts4LCC-BY-NC-4.00Raspberry Pi
Cm4-printing deck
mothenjoyer69
100.4 × 92.9 mm84 parts4LMIT1STM32
Sci board
MatthiasGeorgImhof
80 × 80 mm197 parts4LCC-BY-NC-4.00Front Panel
janni0609
97.8 × 57.3 mm42 parts4LNo license0STM32
AVIONICS BOARD
MatthiasGeorgImhof
80 × 80 mm178 parts4LCC-BY-NC-4.00STM32
OpenLST
MatthiasGeorgImhof
80 × 80 mm171 parts4LCC-BY-NC-4.00Input switch
grahamseamans
57.3 × 17.6 mm10 parts2LNo license0STM32
Sci board wo switches
MatthiasGeorgImhof
80 × 80 mm168 parts4LCC-BY-NC-4.00
How designs wire the MCP23008T-E/SS
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the MCP23008T-E/SS connects to, and the resistors, capacitors and other passives placed on it.
- The A1 pin is tied to GND on 5 of 6 designs.
- The VDD pin has a decoupling capacitor on 4 of 6 designs, most often 100 nF.
- The A2 pin is tied to GND on 4 of 6 designs.
- The A0 pin is tied to GND on 4 of 6 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SCLpin 1 | Connected to: A connector 50%, the microcontroller 50% |
|
| SDApin 2 | Connected to: A connector 50%, the microcontroller 50% |
|
| A2pin 3 | Connected to: GND 67% · 3.3V 17% · a signal 17% | — |
| A1pin 4 | Connected to: GND 83% · 3.3V 17% | — |
| A0pin 5 | Connected to: GND 67% · 3.3V 17% · a signal 17% | — |
| NCpin 7, 10, 11 | Connected to: Not connected 100% | — |
| INTpin 8 | Connected to: The microcontroller 33% · not connected 33% |
|
| VSSpin 9 | Connected to: GND 83% · not connected 17% | — |
| GP4pin 16 | Connected to: Signal 100% |
|
| GP5pin 17 | Connected to: Signal 100% |
|
| GP6pin 18 | Connected to: Signal 83% · not connected 17% |
|
| VDDpin 20 | Connected to: 3.3V 100% |
|
6 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PiADC2 by capconix, UMDv3-kicad by db-electronics, Cm4-printing deck by mothenjoyer69 and Input switch by grahamseamans.
The MCP23008T-E/SS in open source designs
The gallery holds 10 open source boards using the MCP23008T-E/SS from 6 GitHub repositories; a typical one measures about 80 × 80 mm and carries around 126 components.
70% use four copper layers or more, and 20% carry an open source license.
The most starred is Cm4-printing deck by mothenjoyer69.
Microcontrollers on boards using the MCP23008T-E/SS
What boards using the MCP23008T-E/SS are built for
MCP23008T-E/SS: common questions
Where can I find a MCP23008T-E/SS reference design?
Each of the 10 boards on this page is a real design using the MCP23008T-E/SS. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MCP23008T-E/SS A1 pin connected?
The A1 pin is tied to GND on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the MCP23008T-E/SS.
What decoupling capacitors do designs use on the MCP23008T-E/SS VDD pin?
The VDD pin has a decoupling capacitor on 4 of 6 designs, most often 100 nF. Counted from the KiCad layouts of 6 open source designs using the MCP23008T-E/SS.
How is the MCP23008T-E/SS A2 pin connected?
The A2 pin is tied to GND on 4 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the MCP23008T-E/SS.
Which microcontrollers do boards using the MCP23008T-E/SS use?
Most are built on STM32 (6) and Raspberry Pi (1).
How big is a typical board using the MCP23008T-E/SS?
The median is 80 × 80 mm, and 30% are two-layer designs.
What is the most popular open source board using the MCP23008T-E/SS?
By GitHub stars, Cm4-printing deck by mothenjoyer69, with 1 stars.
Can I simulate one of these boards using the MCP23008T-E/SS before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.