11 open source boards using the MCP3002
Real designs built with the MCP3002, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
PedalPiV2
thawney
72.4 × 91.4 mm47 parts2LGPL-3.044Pi plant
rringler
33 × 30.5 mm11 parts2LMIT9Cyclope
RICCIARDI-Adrien
100 × 84 mm75 parts2LMIT5RP2040/RP2350
Procon gcc main
ESCA47
110.9 × 59.5 mm69 parts2LCERN-OHL-S-2.04RP2040/RP2350
V4d2 pico
tomcombriat
54.2 × 94.2 mm99 parts2LTAPR-OHL-1.03RP2040/RP2350
Zinnia2 0 5
plants-tech
125.4 × 90.3 mm70 parts2LCERN-OHL-S-2.02Raspberry Pi
Main PCB (w/o Adaptor)
cinnamondev
95.9 × 83.3 mm145 parts4LCERN-OHL-S-2.01Zatopos ear mic
kazetatsu
80 × 40 mm20 parts2LNo license0RP2040/RP2350
V4d3 pico
tomcombriat
54.2 × 94.2 mm99 parts2LTAPR-OHL-1.03RP2040/RP2350
V4 pico
tomcombriat
54.2 × 95.2 mm96 parts2LTAPR-OHL-1.03RP2040/RP2350
V4d1 pico
tomcombriat
54.2 × 95.2 mm96 parts2LTAPR-OHL-1.03
How designs wire the MCP3002
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the MCP3002 connects to, and the resistors, capacitors and other passives placed on it.
- The CH0 pin has a series resistor on 5 of 8 designs, most often 100 kΩ (then 2 kΩ).
- The VDD/VREF pin has a decoupling capacitor on 4 of 8 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CH0pin 2 | Connected to: A connector 25% |
|
| CH1pin 3 | Connected to: A connector 38% |
|
| VSSpin 4 | Connected to: GND 100% | — |
| VDD/VREFpin 8 | Connected to: 3.3V 75% · a signal 25% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PedalPiV2 by thawney, Pi plant by rringler, Cyclope by RICCIARDI-Adrien and Procon gcc main pcb by ESCA47.
The MCP3002 in open source designs
The gallery holds 11 open source boards using the MCP3002 from 8 GitHub repositories; a typical one measures about 72.4 × 90.3 mm and carries around 75 components.
91% are two-layer designs, the rest use four layers or more, and 91% carry an open source license.
The most starred is PedalPiV2 by thawney.
Parts used alongside the MCP3002
Microcontrollers on boards using the MCP3002
What boards using the MCP3002 are built for
MCP3002: common questions
Where can I find a MCP3002 reference design?
Each of the 11 boards on this page is a real design using the MCP3002. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the MCP3002 CH0 pin?
The CH0 pin has a series resistor on 5 of 8 designs, most often 100 kΩ (then 2 kΩ). Counted from the KiCad layouts of 8 open source designs using the MCP3002.
What decoupling capacitors do designs use on the MCP3002 VDD/VREF pin?
The VDD/VREF pin has a decoupling capacitor on 4 of 8 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 8 open source designs using the MCP3002.
Which microcontrollers do boards using the MCP3002 use?
Most are built on RP2040/RP2350 (6) and Raspberry Pi (1).
How big is a typical board using the MCP3002?
The median is 72.4 × 90.3 mm, and 91% are two-layer designs.
What is the most popular open source board using the MCP3002?
By GitHub stars, PedalPiV2 by thawney, with 44 stars.
Can I simulate one of these boards using the MCP3002 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.