12 open source boards using the MCP6001
Real designs built with the MCP6001, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP8266
Core
plantbot
50 × 50 mm54 parts2LAGPL-3.08M52
rusefi
145 × 118 mm226 parts2LNo license2ESP32
Panel admin-27-white
disobeyfi
250 × 258 mm48 parts2LGPL-3.01STM32
NeuroBytes Cochlea
NeuroTinker
52.3 × 46.5 mm49 parts2LGPL-3.00AVR/Arduino
Sensor node
JacobFV
70 × 45 mm13 parts2LMIT0ADC
FYNCH-BIO
33 × 66 mm98 parts4LNo license12NXP
Top board
mod-audio
170 × 66.6 mm125 parts2LNo license1ESP32
Panel artist-27-purple
disobeyfi
250 × 258 mm48 parts2LGPL-3.01NXP
Top board panel
mod-audio
170 × 135.7 mm125 parts2LNo license1ESP32
Panel hacker-14-black
disobeyfi
250 × 258 mm48 parts2LGPL-3.01ESP32
Panel support-52-blue
disobeyfi
250 × 258 mm48 parts2LGPL-3.01ESP32
Panel user-230-red
disobeyfi
250 × 258 mm48 parts2LGPL-3.01
How designs wire the MCP6001
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the MCP6001 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 2 is tied to GND on 6 of 7 designs.
- Pin 5 is tied to 3.3V on 6 of 7 designs.
- Pin 4 has a series resistor on 4 of 7 designs, most often 1.5 kΩ (then 330 Ω).
- Pin 1 has a series resistor on 3 of 7 designs, most often 1.5 kΩ (then 2 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: A connector 43%, the microcontroller 43% |
|
| Pin 2 | Connected to: GND 86% | — |
| Pin 3 | Connected to: Signal 86% |
|
| Pin 4 | Connected to: Signal 86% |
|
| Pin 5 | Connected to: 3.3V 86% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ADC by FYNCH-BIO, Core pcb by plantbot, M52 by rusefi and Panel admin-27-white by disobeyfi.
The MCP6001 in open source designs
The gallery holds 12 open source boards using the MCP6001 from 7 GitHub repositories; a typical one measures about 170 × 126.8 mm and carries around 49 components.
92% are two-layer designs, the rest use four layers or more, and 67% carry an open source license.
The most starred is ADC by FYNCH-BIO.
Parts used alongside the MCP6001
Microcontrollers on boards using the MCP6001
What boards using the MCP6001 are built for
MCP6001: common questions
Where can I find a MCP6001 reference design?
Each of the 12 boards on this page is a real design using the MCP6001. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MCP6001 pin 2 connected?
Pin 2 is tied to GND on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the MCP6001.
How is the MCP6001 pin 5 connected?
Pin 5 is tied to 3.3V on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the MCP6001.
What resistor goes on the MCP6001 pin 4?
Pin 4 has a series resistor on 4 of 7 designs, most often 1.5 kΩ (then 330 Ω). Counted from the KiCad layouts of 7 open source designs using the MCP6001.
Which microcontrollers do boards using the MCP6001 use?
Most are built on ESP32 (5), NXP (2), AVR/Arduino (1) and ESP8266 (1).
How big is a typical board using the MCP6001?
The median is 170 × 126.8 mm, and 92% are two-layer designs.
What is the most popular open source board using the MCP6001?
By GitHub stars, ADC by FYNCH-BIO, with 12 stars.
Can I simulate one of these boards using the MCP6001 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.