7 open source boards using the MCP73833T-AMI/MF
Real designs built with the MCP73833T-AMI/MF, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Thumbtroller
StuckAtPrototype
74.7 × 30 mm69 parts4LNo license304NXP
Unkey
natecermak
67 × 82.1 mm139 parts4LNo license0Raspberry Pi
Gbczero
hahhen
71.4 × 128 mm78 parts2LNo license0ESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kRP2040/RP2350
Env
es-ude
57.8 × 34 mm181 parts4LMIT4RP2040/RP2350
Elasticnode tiny
es-ude
34 × 34 mm125 parts4LMIT4
How designs wire the MCP73833T-AMI/MF
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the MCP73833T-AMI/MF connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pins have a decoupling capacitor on 5 of 5 designs, most often 10 µF (then 100 nF).
- The PROG pin has a resistor to GND on 5 of 5 designs, most often 5.1 kΩ (then 2 kΩ).
- The PG(TE) pin is left unconnected on 4 of 5 designs.
- The THERM pin has a series resistor on 3 of 5 designs, most often 1.43 kΩ (then 1 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDpin 1, 2 | Connected to: 5V 100% |
|
| VSSpin 5 | Connected to: GND 100% | — |
| PROGpin 6 | Connected to: Signal 100% |
|
| PG(TE)pin 7 | Connected to: Not connected 80% · a signal 20% | — |
| THERMpin 8 | Connected to: Signal 100% |
|
| VBATpin 9, 10 | Connected to: VBAT 60% · a signal 40% |
|
| PADpin 11 | Connected to: GND 100% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Racer by StuckAtPrototype, Thumbtroller by StuckAtPrototype, Elasticnode tiny by es-ude and Gbczero by hahhen.
The MCP73833T-AMI/MF in open source designs
The gallery holds 7 open source boards using the MCP73833T-AMI/MF from 5 GitHub repositories; a typical one measures about 57.8 × 50.2 mm and carries around 78 components.
86% use four copper layers or more, and 57% carry an open source license.
The most starred is Racer by StuckAtPrototype.
Parts used alongside the MCP73833T-AMI/MF
Microcontrollers on boards using the MCP73833T-AMI/MF
What boards using the MCP73833T-AMI/MF are built for
MCP73833T-AMI/MF: common questions
Where can I find a MCP73833T-AMI/MF reference design?
Each of the 7 boards on this page is a real design using the MCP73833T-AMI/MF. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the MCP73833T-AMI/MF VDD pin?
The VDD pins have a decoupling capacitor on 5 of 5 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 5 open source designs using the MCP73833T-AMI/MF.
What resistor goes on the MCP73833T-AMI/MF PROG pin?
The PROG pin has a resistor to GND on 5 of 5 designs, most often 5.1 kΩ (then 2 kΩ). Counted from the KiCad layouts of 5 open source designs using the MCP73833T-AMI/MF.
How is the MCP73833T-AMI/MF PG(TE) pin connected?
The PG(TE) pin is left unconnected on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the MCP73833T-AMI/MF.
Which microcontrollers do boards using the MCP73833T-AMI/MF use?
Most are built on ESP32 (3), RP2040/RP2350 (2), NXP (1) and Raspberry Pi (1).
How big is a typical board using the MCP73833T-AMI/MF?
The median is 57.8 × 50.2 mm, and 14% are two-layer designs.
What is the most popular open source board using the MCP73833T-AMI/MF?
By GitHub stars, Racer by StuckAtPrototype, with 3,798 stars.
Can I simulate one of these boards using the MCP73833T-AMI/MF before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.