5 open source boards using the NB3L553
Real designs built with the NB3L553, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
DSP-ADAU1452
ohdsp
100 × 100 mm377 parts4LTAPR-OHL-1.068Artix7-PCIe
westonb
100 × 115.2 mm196 parts4LNo license34UDSP
ohdsp
50 × 50 mm177 parts4LTAPR-OHL-1.026Narrowband-SDR
BillyWoods
100 × 100 mm463 parts4LNo license16OHDSP-ADAU1452
pwzj
100 × 100 mm376 parts4LTAPR-OHL-1.03
How designs wire the NB3L553
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the NB3L553 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a capacitor to GND on 5 of 5 designs, most often 100 nF (then 22 µF).
- Pin 4 is tied to GND on 5 of 5 designs.
- Pin 2 has a series resistor on 4 of 5 designs, most often 22 Ω (then 75 Ω).
- Pin 3 has a series resistor on 4 of 5 designs, most often 22 Ω (then 75 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 80% · 3.3V 20% |
|
| Pin 2 | Connected to: Signal 100% |
|
| Pin 3 | Connected to: Signal 100% |
|
| Pin 4 | Connected to: GND 100% | — |
| Pin 5 | Connected to: Signal 100% |
|
| Pin 6 | Connected to: Signal 80% · not connected 20% |
|
| Pin 7 | Connected to: Signal 80% · not connected 20% |
|
| Pin 8 | Connected to: Signal 80% · 3.3V 20% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include DSP-ADAU1452 by ohdsp, Artix7-PCIe by westonb, UDSP by ohdsp and Narrowband-SDR by BillyWoods.
The NB3L553 in open source designs
The gallery holds 5 open source boards using the NB3L553 from 5 GitHub repositories; a typical one measures about 100 × 100 mm and carries around 376 components.
100% use four copper layers or more, and 60% carry an open source license.
The most starred is DSP-ADAU1452 by ohdsp.
Parts used alongside the NB3L553
What boards using the NB3L553 are built for
NB3L553: common questions
Where can I find a NB3L553 reference design?
Each of the 5 boards on this page is a real design using the NB3L553. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the NB3L553 pin 1 connected?
Pin 1 has a capacitor to GND on 5 of 5 designs, most often 100 nF (then 22 µF). Counted from the KiCad layouts of 5 open source designs using the NB3L553.
How is the NB3L553 pin 4 connected?
Pin 4 is tied to GND on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the NB3L553.
What resistor goes on the NB3L553 pin 2?
Pin 2 has a series resistor on 4 of 5 designs, most often 22 Ω (then 75 Ω). Counted from the KiCad layouts of 5 open source designs using the NB3L553.
What parts are used alongside the NB3L553?
The ADAU1452WBCPZ, 25AA1024, ADM13307-5ARZ, IC-SPDIF-RX-OPTO and IC-SPDIF-TX-OPTO appear in the most repositories here.
How big is a typical board using the NB3L553?
The median is 100 × 100 mm, and 0% are two-layer designs.
What is the most popular open source board using the NB3L553?
By GitHub stars, DSP-ADAU1452 by ohdsp, with 68 stars.
Can I simulate one of these boards using the NB3L553 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.