7 open source boards using the PCA9306DC
Real designs built with the PCA9306DC, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
Fc980c controller
wlhlm
82.3 × 35.5 mm36 parts2LNo license20ESP32
Minimap
lucapoulos
48 × 55.4 mm74 parts4LNo license2ESP32
Antcontroller
cr1tbit
230 × 160 mm369 parts2LNo license1PRODIGY-MOTHERBOARD
mark69163
160 × 120 mm333 parts4LNo license0AVR/Arduino
RadHardSchematics
FraserD404
203 × 79.7 mm34 parts2LNo license0AVR/Arduino
Rf room sensor hw
dselcan
50.8 × 44 mm32 parts2LBSD-3-Clause010000006 SE
gitlunard
45.9 × 32.3 mm38 parts4LNo license0
How designs wire the PCA9306DC
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the PCA9306DC connects to, and the resistors, capacitors and other passives placed on it.
- The SCL1 pin has a pull-up to 3.3V on 5 of 7 designs, most often 10 kΩ (then 4.7 kΩ).
- The EN pin has a pull-up to 5V on 5 of 7 designs, most often 200 kΩ (then 220 kΩ).
- The SDA1 pin has a pull-up to 3.3V on 3 of 7 designs, most often 10 kΩ (then 4.7 kΩ).
- The SDA2 pin has a pull-up to 3.3V on 3 of 7 designs, most often 10 kΩ (then 4.7 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SCL1pin 3 | Connected to: The microcontroller 29%, a connector 29% |
|
| SDA1pin 4 | Connected to: The microcontroller 29%, a connector 29% · GND 29% |
|
| SDA2pin 5 | Connected to: A connector 57%, the microcontroller 43% |
|
| SCL2pin 6 | Connected to: A connector 57%, the microcontroller 43% |
|
| ENpin 8 | Connected to: Signal 86% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Fc980c controller by wlhlm, Minimap by lucapoulos, Antcontroller by cr1tbit and Rf room sensor hw by dselcan.
The PCA9306DC in open source designs
The gallery holds 7 open source boards using the PCA9306DC from 7 GitHub repositories; a typical one measures about 82.3 × 55.4 mm and carries around 38 components.
57% are two-layer designs, the rest use four layers or more, and 14% carry an open source license.
The most starred is Fc980c controller by wlhlm.
Parts used alongside the PCA9306DC
Microcontrollers on boards using the PCA9306DC
What boards using the PCA9306DC are built for
PCA9306DC: common questions
Where can I find a PCA9306DC reference design?
Each of the 7 boards on this page is a real design using the PCA9306DC. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the PCA9306DC SCL1 pin?
The SCL1 pin has a pull-up to 3.3V on 5 of 7 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 7 open source designs using the PCA9306DC.
What pull-up resistor is used on the PCA9306DC EN pin?
The EN pin has a pull-up to 5V on 5 of 7 designs, most often 200 kΩ (then 220 kΩ). Counted from the KiCad layouts of 7 open source designs using the PCA9306DC.
What pull-up resistor is used on the PCA9306DC SDA1 pin?
The SDA1 pin has a pull-up to 3.3V on 3 of 7 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 7 open source designs using the PCA9306DC.
Which microcontrollers do boards using the PCA9306DC use?
Most are built on AVR/Arduino (2), ESP32 (2) and RP2040/RP2350 (1).
How big is a typical board using the PCA9306DC?
The median is 82.3 × 55.4 mm, and 57% are two-layer designs.
What is the most popular open source board using the PCA9306DC?
By GitHub stars, Fc980c controller by wlhlm, with 20 stars.
Can I simulate one of these boards using the PCA9306DC before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.