7 open source boards using the RTL8201F-VB-CG
Real designs built with the RTL8201F-VB-CG, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Iot esp eth com
uysan
29.5 × 64.5 mm146 parts4LCERN-OHL-P-2.019KiCad-EXT-PHY-RTL8201F
vanvught
56.8 × 22.8 mm32 parts2LMIT2ESP32
Lichtstab
kilimnik
100.5 × 87.7 mm139 parts4LNo license0ESP32
Cadlab test
LPfueller
105 × 75 mm74 parts4LNo license0ESP32
Crino temp ecad
LPfueller
105 × 75 mm74 parts4LNo license0RISC-V
Adin1100 podl
dragonlock2
72 × 24 mm125 parts2LApache-2.013NXP
Lpc1768 poe
dragonlock2
69 × 23 mm116 parts4LApache-2.013
How designs wire the RTL8201F-VB-CG
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the RTL8201F-VB-CG connects to, and the resistors, capacitors and other passives placed on it.
- The RSET pin has a resistor to GND on 6 of 6 designs, most often 2.49 kΩ (then 2.49 Ω).
- The AVDD10OUT pin has a capacitor to GND on 6 of 6 designs, most often 100 nF.
- The AVDD33 pins have a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 47 µF).
- The RXDV pin has a pull-up to 3.3V on 6 of 6 designs, most often 4.7 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| RSETpin 1 | Connected to: Signal 100% |
|
| AVDD10OUTpin 2 | Connected to: Signal 100% |
|
| MDI+[0]pin 3 | Connected to: A connector 50% |
|
| MDI-[0]pin 4 | Connected to: A connector 50% |
|
| MDI+[1]pin 5 | Connected to: A connector 50% |
|
| MDI-[1]pin 6 | Connected to: A connector 50% |
|
| AVDD33pin 7, 30 | Connected to: 3.3V 67% · a signal 33% |
|
| RXDVpin 8 | Connected to: Signal 100% |
|
| RXD[0]pin 9 | Connected to: Signal 100% |
|
| RXD[1]pin 10 | Connected to: Signal 100% |
|
| RXD[2]/INTBpin 11 | Connected to: Not connected 83% · a signal 17% | — |
| RXD[3]/CLK_CTLpin 12 | Connected to: Not connected 83% · a signal 17% | — |
| RXCpin 13 | Connected to: Not connected 100% | — |
| DVDD33pin 14 | Connected to: 3.3V 100% |
|
| TXCpin 15 | Connected to: Not connected 67% · a signal 33% | — |
| TXD[0]pin 16 | Connected to: The microcontroller 50% |
|
| TXD[1]pin 17 | Connected to: The microcontroller 50% |
|
| TXD[2]pin 18 | Connected to: Not connected 100% | — |
| TXD[3]pin 19 | Connected to: Not connected 100% | — |
| PHYRSTBpin 21 | Connected to: The microcontroller 83%, a connector 33% |
|
| MDCpin 22 | Connected to: The microcontroller 83% |
|
| MDIOpin 23 | Connected to: The microcontroller 83% |
|
| LED0/PHYAD[0]/PMEBpin 24 | Connected to: A connector 33% |
|
| LED1/PHYAD[1]pin 25 | Connected to: A connector 33% |
|
| COLpin 27 | Connected to: Not connected 100% | — |
| RXER/FXENpin 28 | Connected to: Not connected 83% · a signal 17% | — |
| DVDD10OUTpin 29 | Connected to: Signal 100% |
|
| CKXTAL1pin 31 | Connected to: GND 67% · a signal 33% |
|
| CKXTAL2pin 32 | Connected to: A connector 50%, the microcontroller 50% |
|
| EPpin 33 | Connected to: GND 100% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Iot esp eth com by uysan, Adin1100 podl by dragonlock2, KiCad-EXT-PHY-RTL8201F by vanvught and Lichtstab by kilimnik.
The RTL8201F-VB-CG in open source designs
The gallery holds 7 open source boards using the RTL8201F-VB-CG from 6 GitHub repositories; a typical one measures about 72 × 64.5 mm and carries around 116 components.
71% use four copper layers or more, and 57% carry an open source license.
The most starred is Iot esp eth com by uysan.
Parts used alongside the RTL8201F-VB-CG
What boards using the RTL8201F-VB-CG are built for
RTL8201F-VB-CG: common questions
Where can I find a RTL8201F-VB-CG reference design?
Each of the 7 boards on this page is a real design using the RTL8201F-VB-CG. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the RTL8201F-VB-CG RSET pin?
The RSET pin has a resistor to GND on 6 of 6 designs, most often 2.49 kΩ (then 2.49 Ω). Counted from the KiCad layouts of 6 open source designs using the RTL8201F-VB-CG.
How is the RTL8201F-VB-CG AVDD10OUT pin connected?
The AVDD10OUT pin has a capacitor to GND on 6 of 6 designs, most often 100 nF. Counted from the KiCad layouts of 6 open source designs using the RTL8201F-VB-CG.
What decoupling capacitors do designs use on the RTL8201F-VB-CG AVDD33 pin?
The AVDD33 pins have a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 47 µF). Counted from the KiCad layouts of 6 open source designs using the RTL8201F-VB-CG.
What parts are used alongside the RTL8201F-VB-CG?
The AG9912M, ESP32-WROVER-IE-N4R8, PAC1932T-I/JQ, PCA9536TK,118 and SY8120IABC appear in the most repositories here.
Which microcontrollers do boards using the RTL8201F-VB-CG use?
Most are built on ESP32 (4), NXP (1) and RISC-V (1).
How big is a typical board using the RTL8201F-VB-CG?
The median is 72 × 64.5 mm, and 29% are two-layer designs.
What is the most popular open source board using the RTL8201F-VB-CG?
By GitHub stars, Iot esp eth com by uysan, with 19 stars.
Can I simulate one of these boards using the RTL8201F-VB-CG before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.