5 open source boards using the RYLR998
Real designs built with the RYLR998, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
RelativeGPS
m-guihard
65 × 65 mm91 parts4LNo license0ESP32
TankSync tx
gargsrishtii
100 × 100 mm38 parts2LCERN-OHL-P-2.00ESP32
Kicad document generator
gargsrishtii
81 × 50 mm20 parts2LNo license0ESP32
TankSync-RX
gargsrishtii
81 × 50 mm20 parts2LCERN-OHL-P-2.00Donglev1
WaltTeb
16.6 × 21.5 mm15 parts2LNo license3
How designs wire the RYLR998
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the RYLR998 connects to, and the resistors, capacitors and other passives placed on it.
- The NRST_2 pin has a pull-up to 3.3V on 2 of 5 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDD_1pin 1 | Connected to: 3.3V 60% · GND 20% · a signal 20% | — |
| NRST_2pin 2 | Connected to: The microcontroller 60%, a connector 40% |
|
| GND_5pin 5 | Connected to: GND 80% · a signal 20% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Donglev1 by WaltTeb, Kicad document generator by gargsrishtii, TankSync-RX by gargsrishtii and TankSync tx by gargsrishtii.
The RYLR998 in open source designs
The gallery holds 5 open source boards using the RYLR998 from 5 GitHub repositories; a typical one measures about 81 × 50 mm and carries around 20 components.
80% are two-layer designs, the rest use four layers or more, and 40% carry an open source license.
The most starred is Donglev1 by WaltTeb.
Parts used alongside the RYLR998
What boards using the RYLR998 are built for
RYLR998: common questions
Where can I find a RYLR998 reference design?
Each of the 5 boards on this page is a real design using the RYLR998. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the RYLR998 NRST_2 pin?
The NRST_2 pin has a pull-up to 3.3V on 2 of 5 designs, most often 10 kΩ. Counted from the KiCad layouts of 5 open source designs using the RYLR998.
Which microcontrollers do boards using the RYLR998 use?
Most are built on ESP32 (3) and STM32 (1).
How big is a typical board using the RYLR998?
The median is 81 × 50 mm, and 80% are two-layer designs.
What is the most popular open source board using the RYLR998?
By GitHub stars, Donglev1 by WaltTeb, with 3 stars.
Can I simulate one of these boards using the RYLR998 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.